Housing (Front) - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 4C-9612 | Silicone Sealant | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to the bottom of front housing (11) at the junction of the cylinder block and the engine oil pan.
- Attach a suitable lifting device to front housing (11). The weight of front housing (11) is approximately
70 kg (154 lb) . Position the gasket and front housing (11) on the dowel pins on the cylinder block. - Install bolts (13) and bolts (12).
- Trim the gasket between the front housing and the cylinder block even with the bottom of the front housing.
- Install adapters (10).
Show/hide table
Illustration 2 g01204127 Show/hide tableIllustration 3 g01151441 - Install dampers (9) and bolts (8).
- Tighten bolts (8) to a torque of
240 ± 40 N·m (177 ± 30 lb ft) . Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.Show/hide tableIllustration 4 g01204024 - Reposition the fuel filter assembly and tighten bolts (5).
- Connect harness assembly (7).
- Install covers (1).
- Install brackets (2) and (6).
- Install tube assemblies (3) and hose assemblies (4).
Show/hide table
Illustration 1 | g01204142 |
End By:
- Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
- Install the exhaust elbow, if necessary. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
- Install the turbocharger, if necessary. Refer to Disassembly and Assembly, "Turbocharger - Install".
- Install the front engine support. Refer to Disassembly and Assembly, "Engine Trunnion - Remove and Install".
- Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Caterpillar Information System:
3500B and 3500C Generator Set Engines Coolant Level Sensor
3500B and 3500C Generator Set Engines E552 Low Aftercooler Coolant Level
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Shuttle Valve (Counterweight Circuit) - Install
C13, C15, and C18 Tier 4 Final Engines Flywheel Housing
3412 Generator Set Engines Flywheel
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Shuttle Valve (Counterweight Circuit) - Assemble
3412 Generator Set Engines Flywheel
3406C Engines for Caterpillar Built Machines Flywheel Housing
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Shuttle Valve (Counterweight Circuit) - Disassemble
3406C Engines for Caterpillar Built Machines Flywheel Housing
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Counterweight Circuit) - Assemble
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Load Control Valve (Boom Cylinder) - Install
315D, 318D and 319D Excavators Machine Systems Auxiliary Pilot Valve (Straight Travel) - Disassemble
C27 and C32 Generator Set Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Boom - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Window Wiper Motor - Remove and Install - Upper
315D, 318D and 319D Excavators Machine Systems Auxiliary Pilot Valve (Straight Travel) - Assemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Valve Lifter - Disassemble
C32 Petroleum Engines Valve Mechanism Cover - Remove and Install
3508 EUI Engine for D11N and D11R Track-Type Tractors Installation and Removal of the Speed/Timing Sensor
C1.5 and C2.2 Generator Set Engines Radiator - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Valve Lifter - Assemble
Reuse and Salvage for 3000 Engine Series Cylinder Blocks {1201} Reuse and Salvage for 3000 Engine Series Cylinder Blocks {1201}
3412 Generator Set Engines Fuel Shutoff Solenoid