Flywheel Housing
Show/hide table
 | |
| 图 1 | g02646983 |
Show/hide table
 | |
| 图 2 | g02646984 |
Show/hide table
| 134-2809 飞轮壳体总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 在组装过程中，检查下列部件有无任何异物：飞轮壳体的前端面、飞轮壳体密封垫的两侧和缸体的后端面。 这些部件必须没有以下物质：机油、燃油、水、粘合剂、组装固定胶和任何其他异物。 涂覆超蓝 Loctite 587 以便填充缸体、飞轮壳体和油底壳之间的空隙。 涂抹密封剂 10 分钟内必须组装好部件。 | |||
| 1 | 9 | 7K-6058 螺栓 | 按照下列步骤拧紧飞轮壳体的螺栓： 1. 按照图 2 中所示的数字顺序将螺栓 1 至 9 拧紧至扭矩为 100 ± 20 N·m (75 ± 15 lb ft)。 2. 按照图 2 中所示的数字顺序将螺栓 10 至 24 拧紧至扭矩为 40 ± 10 N·m (30 ± 7 lb ft)。 3. 再次按照图 2 中所示的数字顺序将螺栓 1 至 9 拧紧至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。 4. 按照图 2 中所示的数字顺序将螺栓 10 至 24 拧紧至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。 |
| 2 | 8 | 165-3929 螺栓 | |
| 3 | 7 | 165-3933 螺栓 | |
| 4 | 3 | 4B-4043 螺栓 | 拧紧至扭矩为 115 ± 20 N·m (85 ± 15 lb ft)。 |
Caterpillar Information System:
3412 Generator Set Engines Flywheel
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Shuttle Valve (Counterweight Circuit) - Assemble
3412 Generator Set Engines Flywheel
3406C Engines for Caterpillar Built Machines Flywheel Housing
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Shuttle Valve (Counterweight Circuit) - Disassemble
3406C Engines for Caterpillar Built Machines Flywheel Housing
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Counterweight Circuit) - Assemble
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Load Control Valve (Boom Cylinder) - Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C9 Generator Set Engines Sensors and Electrical Connectors
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Counterweight Circuit) - Disassemble
C32 Petroleum Engines Housing (Front) - Remove
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Shuttle Valve (Counterweight Circuit) - Install
3500B and 3500C Generator Set Engines E552 Low Aftercooler Coolant Level
3500B and 3500C Generator Set Engines Coolant Level Sensor
C32 Petroleum Engines Housing (Front) - Install
315D, 318D and 319D Excavators Machine Systems Auxiliary Pilot Valve (Straight Travel) - Disassemble
C27 and C32 Generator Set Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Boom - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Window Wiper Motor - Remove and Install - Upper
315D, 318D and 319D Excavators Machine Systems Auxiliary Pilot Valve (Straight Travel) - Assemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Valve Lifter - Disassemble
C32 Petroleum Engines Valve Mechanism Cover - Remove and Install
3508 EUI Engine for D11N and D11R Track-Type Tractors Installation and Removal of the Speed/Timing Sensor