Hydraulic Tank - Assemble
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 1P-1855     | 挡圈钳     | 1     |
C     | 3G-4090     | 密封胶     | 1     |
- 将 O 形密封圈 (48) 安装到油位传感器 (46) 上。
Show/hide table
图 1 | g01101588 |
- 将 O 形密封圈 (47) 安装到油位传感器 (45) 上。
Show/hide table
图 2 | g01101587 |
- 安装油位传感器 (45) 和油温传感器 (46) 。
Show/hide table
图 3 | g01101576 |
- 安装盖 (41) 、滤清器 (42) 、O 形密封圈 (43) 和套筒 (44) 。 利用工具 (B) 安装挡圈 (40) 。
Show/hide table
图 4 | g01101570 |
- 安装呼吸器组件 (39) 。
Show/hide table
图 5 | g01101568 |
- 将 O 形密封圈 (38) 安装到排放塞 (37) 上。 将排放塞 (37) 装入排放阀 (32) 中。 安装 O 形密封圈 (33) 。 安装阀 (34) 、弹簧 (35) 和阀导管 (36) 。
Show/hide table
图 6 | g01101559 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装排放阀 (32) 。 安装螺母 (31) 。
Show/hide table
图 7 | g01101557 |
- 将滤网 (30) 和锁环 (29) 装入加注管中。
Show/hide table
图 8 | g01101555 |
- 将钢球 (24) 、板 (25) 和密封垫 (26) 装入加注口盖 (23) 中。
将加注口盖 (23) 、环 (27) 和挡圈 (28) 装入盖 (22) 中。
Show/hide table
图 9 | g01101549 |
Show/hide table
图 10 | g01101550 |
- 安装垫圈、O 形密封圈和管组件 (21) 。 安装螺栓 (20) 。
Show/hide table
图 11 | g01101546 |
- 安装垫圈、O 形密封圈和管组件 (19) 。 安装螺栓 (18) 。
Show/hide table
图 12 | g01101480 |
- 安装板 (15) 、护线环 (16) 和观察窗 (17) 。 将 O 形密封圈 (14) 安装到护圈 (11) 上。
Show/hide table
图 13 | g01101474 |
- 安装仪表组件 (13) 和护圈 (11) 。 固定护圈 (11) 的同时安装螺栓 (12) 。
Show/hide table
图 14 | g01101454 |
Show/hide table
图 15 | g01101455 |
- 清除液压油箱两半体密封面上用过的密封胶。 彻底清理液压油箱两半体的密封面。
Show/hide table
图 16 | g01101783 |
- 将工具 (C) 涂抹到液压油箱的一个半体上。 搭接工具 (C) 的边缘,如图所示。
- 将工具 (A) 固定到液压油箱 (1) 上。 如图所示,将适当的起吊设备固定到工具 (A) 上。 液压油箱半体的重量约为 125 kg (275 lb)。 利用适当的起吊设备安装液压油箱 (1) 的上半体。
Show/hide table
图 17 | g01101446 |
- 安装螺栓 (10) 。 将螺栓 (8) 和托架 (9) 安装到油箱组件 (1) 上。
Show/hide table
图 18 | g01101449 |
- 利用适当的起吊设备定位液压油箱。 安装夹子 (7) 。
Show/hide table
图 19 | g01101442 |
- 将适当的起吊设备连接到板 (6) 上,如图所示。 板 (6) 的重量约为 80 kg (175 lb)。 安装板 (6) 。
Show/hide table
图 20 | g01101440 |
- 安装螺栓 (4) 。 连接线束组件 (5) 。
Show/hide table
图 21 | g01101435 |
- 将扶梯 (3) 安装到液压油箱 (1) 上。 安装螺栓 (2) 。
Show/hide table
图 22 | g01101433 |
End By: 安装液压油箱。 请参阅 拆解和组装, "液压油箱 - 安装"。
Caterpillar Information System:
966H and 972H Wheel Loaders Roading Fender Control - If Equipped
966H and 972H Wheel Loaders Hood Tilt
D9T Track-Type Tractor Machine Systems Piston Motor (Hydraulic Fan) - Remove
AccuGrade Laser System Display Icons
2004/10/04 Serviceable Parts for the Gear Pump Now Available {5073}
525C, 535C and 545C Wheel Skidders Transmission Oil Filter - Replace
525C, 535C and 545C Wheel Skidders Transmission Oil - Change
525C, 535C and 545C Wheel Skidders Brake Accumulator - Check
525C, 535C and 545C Wheel Skidders Stopping the Engine
525C, 535C and 545C Wheel Skidders Engine and Machine Warm-Up
525C, 535C and 545C Wheel Skidders Parking Brake
525C, 535C and 545C Wheel Skidders Secondary Steering - If Equipped
D9T Track-Type Tractor Machine Systems Piston Motor (Hydraulic Fan) - Install
C15 and C18 Generator Set Engines Engine Oil Pump - Disassemble
C15 and C18 Generator Set Engines Engine Oil Pump - Assemble
D9T Track-Type Tractor Engine Supplement Vibration Damper and Pulley - Remove and Install
2004/09/06 Improved Process for Machine Transportation {7000}
988H Wheel Loader Electrohydraulic System Pressure Sensor (Lift Cylinder Head End Oil) (Lift Cylinder Rod End Oil)
D9T Track-Type Tractor Engine Supplement Hydraulic Oil Cooler (Differential Steering) - Remove and Install
980H Wheel Loader Machine Systems Electrohydraulic Control - Remove
D9T Track-Type Tractor Engine Supplement Engine Front Support and Trunnion - Remove
2004/09/01 New Turbocharger Compressor Cover {1052}
930G Wheel Loader Power Train Electrical Input Components
C7 and C9 Engines for Caterpillar Built Machines Cat Data Link Circuit - Test