Camshaft - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 282-9962     | 导管     | 2     |
B     | 255-2820     | 凸轮轴导向器     | 2     |
C     | 8T-3169     | 曲轴组件     | 1     |
开始:
- 拆卸气门挺杆。 请参阅拆解和组装, "气门挺杆 - 拆卸"。
- 排空冷却系统中的冷却液。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 断开线束组件 (1) 。 卸下螺栓 (2) 。 拆下盖 (3) 。 卸下螺栓 (4) 。 拆下提升支架 (5) 。
Show/hide table
图 1 | g01228199 |
- 拆下螺栓 (6) 。 拆下盖 (7) 。
Show/hide table
图 2 | g01228201 |
- 拆下螺栓 (8) 。 拆下螺栓 (9) 。 拆下隔套 (10) 。 拆下凸轮齿轮 (11) 。
Show/hide table
图 3 | g01228235 |
- 拆下螺栓 (12) 和垫圈。 拆下护圈 (13) 。
Show/hide table
图 4 | g01228236 |
- 断开管组件 (14) 。 拆下螺栓 (15) 。 取下壳体 (16) 。
Show/hide table
图 5 | g01228238 |
- 拆卸管组件 (17) 。 拆下螺栓 (18) 。 取下壳体 (19) 。
Show/hide table
图 6 | g01228240 |
- 将一薄层机油涂抹在工具 (A) 和工具 (B) 上。 安装工具 (A) 并保持螺栓松动。 安装工具 (B) 。 拧紧工具 (A) 的螺栓。 安装工具 (C) 。 使用工具 (C) 转动凸轮轴。 转动凸轮轴以将其拆下。
注: 凸轮轴可从发动机任一端拆下。
Show/hide table
图 7 | g01228274 |
典型示例 |
Show/hide table
图 8 | g01228276 |
典型示例 |
- 从发动机上将凸轮轴 (20) 拆下一半。 使用适当的起吊设备支撑凸轮轴 (20) 。 凸轮轴 (20) 的重量约为 95 kg (210 lb)。 拆下凸轮轴 (20) 的其余部分。
Show/hide table
图 9 | g01228315 |
Caterpillar Information System:
3500 Engines for Caterpillar Built Machines Manual Shutoff
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover
C1.5 and C2.2 Generator Set Engines Crankshaft Pulley - Remove and Install
C1.5 and C2.2 Generator Set Engines Flywheel Housing - Remove and Install
C175 Generator Set Engines Exhaust Manifold - Remove and Install
C15 Petroleum Generator Set Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism
3500B Series II Marine Engines Replacing the ECM
C1.5 and C2.2 Generator Set Engines Flywheel Housing - Remove and Install
C1.5 and C2.2 Generator Set Engines Crankshaft Rear Seal - Install
C1.5 and C2.2 Generator Set Engines Crankshaft Rear Seal - Remove
C27 and C32 Industrial and Petroleum Engines Air Inlet and Exhaust Lines
C1.5 and C2.2 Generator Set Engines Valve Mechanism Cover - Remove and Install
Index of Wall Charts for Drivetrain, Engine, Hydraulics, and Undercarriage{1000, 4000, 4150, 5050} Index of Wall Charts for Drivetrain, Engine, Hydraulics, and Undercarriage{1000, 4000, 4150, 5050}
Shop Repair Procedure for Grease Lubricated Track {0729, 4169, 4170, 4175} Shop Repair Procedure for Grease Lubricated Track {0729, 4169, 4170, 4175}
TH48-E80 Petroleum Transmission Power Train Electronic Control System Shift Inhibit Function
C27 and C32 Generator Set Engines CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C27 and C32 Generator Set Engines CID 0175 FMI 04 Engine Oil Temperature short to ground
C15-XQ400 Rental Generator Set Model View Illustrations
C9 On-highway Engine Engine Oil Pan
C15 Generator Set Engines Event Codes
C15 Generator Set Engines E085 Engine Shutdown Overridden
C27 and C32 Generator Set Engines E096 High Fuel Pressure
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan