Flywheel Housing - Remove and Install
Removal Procedure
Start By:
- Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Support the engine with a suitable lifting device or support the engine on blocks that are positioned on a flat level surface.
- Remove bolts (2) and flywheel housing (1) .
Show/hide table
Illustration 1 | g01199060 |
Typical example |
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-9612     | Silicone Sealant     | -     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the rear face of the cylinder block and the mating face of flywheel housing (1). Inspect the crankshaft rear seal for leaks. Inspect the dowels for damage. If the crankshaft rear seal or the dowels are damaged, use new parts for replacement.
Show/hide table
Illustration 2 | g01199060 |
Typical example |
- Apply a continuous bead of Tooling (A) to the rear face of the cylinder block around the mating surface of the crankshaft rear seal and around the rear core plug for the camshaft.
- Position flywheel housing (1) on the dowels.
- Install bolts (2). Tighten the bolts to a torque of 25 N·m (19 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar Information System:
C175 Generator Set Engines Exhaust Manifold - Remove and Install
C15 Petroleum Generator Set Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism
3500B Series II Marine Engines Replacing the ECM
C1.5 and C2.2 Generator Set Engines Flywheel Housing - Remove and Install
C1.5 and C2.2 Generator Set Engines Crankshaft Rear Seal - Install
C1.5 and C2.2 Generator Set Engines Crankshaft Rear Seal - Remove
C27 and C32 Industrial and Petroleum Engines Air Inlet and Exhaust Lines
C32 Auxiliary Engine Fuel and the Effect from Cold Weather
C15 Petroleum Generator Set Engines Vibration Damper and Pulley
C4.4 and C6.6 Engines for Caterpillar Built Machines CID 0247 FMI 12
G3500 Engines Control Panel
C1.5 and C2.2 Generator Set Engines Crankshaft Pulley - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover
3500 Engines for Caterpillar Built Machines Manual Shutoff
C175 Generator Set Engines Camshaft - Remove
C1.5 and C2.2 Generator Set Engines Valve Mechanism Cover - Remove and Install
Index of Wall Charts for Drivetrain, Engine, Hydraulics, and Undercarriage{1000, 4000, 4150, 5050} Index of Wall Charts for Drivetrain, Engine, Hydraulics, and Undercarriage{1000, 4000, 4150, 5050}
Shop Repair Procedure for Grease Lubricated Track {0729, 4169, 4170, 4175} Shop Repair Procedure for Grease Lubricated Track {0729, 4169, 4170, 4175}
TH48-E80 Petroleum Transmission Power Train Electronic Control System Shift Inhibit Function
C27 and C32 Generator Set Engines CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C27 and C32 Generator Set Engines CID 0175 FMI 04 Engine Oil Temperature short to ground
C15-XQ400 Rental Generator Set Model View Illustrations
C9 On-highway Engine Engine Oil Pan