D10R Track-Type Tractor Caterpillar


Daily Inspection

Usage:

D10R 3KR

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

At operating temperature, the engine coolant is hot and under pressure.

Steam can cause personal injury.

Check the coolant level only after the engine has been stopped and the cooling system pressure cap is cool enough to touch with your bare hand.

Remove the cooling system pressure cap slowly to relieve pressure.

Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.



NOTICE

Accumulated grease and oil on a machine is a fire hazard. Remove this debris with steam cleaning or high pressure water, at least every 1000 hours or each time any significant quantity of oil is spilled on a machine.


For maximum service life of the machine, perform a thorough walk-around inspection before you mount the machine and before you start the engine.

Look around the machine and under the machine. Look for trash buildup, dirt buildup, loose bolts, oil leaks, coolant leaks, broken parts, cracked parts or worn parts.

Note: Watch closely for leaks. If you observe a leak, find the source of the leak and correct the leak. If you suspect a leak or you observe a leak, check the fluid levels more frequently.

Inspect the condition of the equipment and of the hydraulic components.

Check the oil levels, the coolant level, and the fuel level.

Remove any trash buildup and debris. Make all necessary repairs before you operate the machine.

Make sure that all covers and guards are securely attached.

The operator should be seated against the seat backrest. Adjust the seat so that the operator is allowed full travel of the pedals.

Adjust the mirrors for the correct rear view of the machine.

Make sure that the engine air filter service indicator for the tractor is not in the red zone. Make sure that the engine air filter service indicator for the scraper is not in the red zone.

Grease all of the fittings that need to be serviced on a daily basis.

Daily, perform the procedures that are applicable to your machine:

  • Operation and Maintenance Manual, "Backup Alarm - Test"

  • Operation and Maintenance Manual, "Brakes, Indicators and Gauges - Test"

  • Operation and Maintenance Manual, "Cooling System Level - Check"

  • Operation and Maintenance Manual, "Differential and Final Drive Oil Level - Check"

  • Operation and Maintenance Manual, "Engine Air Precleaner - Clean"

  • Operation and Maintenance Manual, "Engine Oil Level - Check"

  • Operation and Maintenance Manual, "Fuel System Water Separator - Drain"

  • Operation and Maintenance Manual, "Fuel Tank Water and Sediment - Drain"

  • Operation and Maintenance Manual, "Hydraulic Oil Cooler - Clean"

  • Operation and Maintenance Manual, "Hydraulic System Oil Level - Check"

  • Operation and Maintenance Manual, "Radiator Core - Clean"

  • Operation and Maintenance Manual, "Seat Belt - Inspect"

  • Operation and Maintenance Manual, "Transmission Oil Level - Check"

Caterpillar Information System:

2004/04/12 An Updated Lines Group Improves Reliability In Certain Conditions {5057, 6203}
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine Supplement Steering Frame Lock - Separate and Connect
2004/03/22 A New Rear Cluster Idler Gear is Available {1204}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Bank Valve - Assemble
2004/03/22 A New Retainer Plate For The Final Drive Bearing And Thrust Washer Improves The Service Life {4050}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Bank Valve - Disassemble
D5N and D6N Track-Type Tractors AccuGrade Laser Startup (Dual Mast System)
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Hydraulic System Pressure - Release
AD30 Underground Articulated Truck Output Transfer Gears - Disassemble
D10R Track-Type Tractor Emissions Certification Film
SCJ and 8SC Series Alternators Charging System
906 and 908 Wheel Loaders Hydraulic and Steering System Steering System
854G Wheel Dozer Hydraulic System Main Control Valve
D10R Track-Type Tractor Seat
992G Wheel Loader and 854G Wheel Dozer Power Train Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
992G Wheel Loader and 854G Wheel Dozer Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Electronic Technician) - Calibrate
992G Wheel Loader and 854G Wheel Dozer Power Train Position Sensor (Left Brake Pedal) (Electronic Technician) - Calibrate
Product Link PL-102C System Installation{7606} Product Link PL-102C System Installation{7606}
2004/05/10 New Test ECM Available for Machines {0785, 7610}
AD45B Underground Articulated Truck Power Train Output Transfer Gears - Disassemble
AD45B Underground Articulated Truck Power Train Output Transfer Gears - Assemble
902, 906 and 908 Compact Wheel Loaders Maintenance Interval Schedule - 902 Compact Wheel Loaders
2004/03/22 New Thrust Discs Improve the Service Life of the Planetary Carriers and the Planetary Gear Mills {3030}
902, 906 and 908 Compact Wheel Loaders Maintenance Interval Schedule - 906 and 908 Compact Wheel Loaders
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.