Engine Mount - Install - Front
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
- 将适当的起吊设备连接到发动机 (3) 。 发动机 (3) 的重量约为 680 kg (1500 lb)。 给发动机 (3) 施加一个轻微的起吊压力。
Show/hide table
图 1 | g01192618 |
- 安装橡胶底座 (6) 、垫片 (5) 、螺栓 (4) 和螺母 (7) 。
Show/hide table
图 2 | g01192621 |
- 对于另一侧,重复步骤2。
- 降下发动机,并拧紧螺母 (4) 。 将螺栓 (4) 拧紧至扭矩为 900 ± 100 N·m (664 ± 74 lb ft)。
- 将工具 (A) 和适当的起吊设备连接在支承 (1) 上。 支承 (1) 的重量约为 34 kg (75 lb)。 安装支承 (1) 。 安装支架 (2) 。
Show/hide table
图 3 | g01192606 |
End By:
- 安装底部防护罩。 请参阅 拆解和组装, "底部防护罩 - 安装"。
- 安装发动机罩。 请参阅 拆解和组装, "发动机罩 - 安装"。
Caterpillar Information System:
3412E Petroleum Engine Front Cover - Remove
2005/08/22 Improved Gasket for the Jacket Water Pump {1361}
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0826 - FMI 03
2005/08/15 New Torque Procedure for the Exhaust Elbow {1061}
3412E Petroleum Engine Vibration Damper and Pulley - Remove and Install
2005/08/15 Improved Ignition Transformers are Used {4476}
3412E Petroleum Engine Flywheel Housing - Remove and Install
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0672 - FMI 08
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0672 - FMI 02
3412E Petroleum Engine Flywheel - Install
3412E Petroleum Engine Flywheel - Remove
C-12 Generator Set Engine Electrical Power Supply Circuit - Test
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Engine Mount - Remove - Rear
C4.4 and C6.6 Engines for Caterpillar Built Machines ECM Memory - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Throttle Switch Circuit - Test
3412E Petroleum Engine Front Cover - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Selector Valve (Alternate Pattern Control) - Disassemble
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Selector Valve (Alternate Pattern Control) - Assemble
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0826 - FMI 04
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Engine Mount - Install - Rear
C27 and C32 Engines for Caterpillar Built Machines CID 0174 FMI 03 Fuel Temperature open/short to +batt
C7.1 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
2005/08/01 An Improved Idler Pulley Has Been Released {1358}
3412E Petroleum Engine Crankcase Breather - Remove and Install