Lockup Clutch and Solenoid Valve (Torque Converter) - Remove
拆卸步骤
注: 为便于安装，在所有软管、所有软管组件、所有导线及所有管组件上做出识别标记。 插接好所有软管组件和所有管子组件。 这将有助于防止液体渗漏，并有助于防止污物进入系统。
注: 清洁度是一项重要的因素。 开始进行拆卸步骤之前，应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 检查 O 形密封圈、密封垫和密封是否磨损或损坏。 必要时，更换部件。
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修发动机时，请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前，要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品，请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 断开线束组件 (1) 和软管组件 (2) 。
Show/hide table
 | |
| 图 1 | g01186213 |
- 卸下螺栓 (3) 及锁定离合器和电磁阀 (4) 。
Caterpillar Information System:
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Starting and Stopping
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Assemble
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Disassemble
2005/08/15 Improved Spin-On Engine Oil Filters are Used {1308}
C6.6 Industrial Engine Crankcase Breather
C13 and C15 On-highway Engines Engine Speed - Test
C13 and C15 On-highway Engines Sensor Supply - Test
C13 and C15 On-highway Engines Shutdown Timer (PTO) - Test
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Install
3618 Engine Auxiliary Water Pump - Disassemble
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Remove
C9 Generator Set Electronic Modular Control Panel 3 (EMCP 3)
C15 On-Highway Engine Fuel System - Prime
C-12 Generator Set Engine CID 0091 FMI 08 Throttle Position signal abnormal
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Install
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Disassemble
3618 Engine Auxiliary Water Pump - Assemble
3456 Generator Sets Starting the Engine - EMCP 3 (If Equipped)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Device Bus Network - Modbus Communications
3456 Generator Sets Manual Stop Procedure
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Assemble
C6.6 Engines for Caterpillar Built Machines Crankshaft Seals
2005/07/01 Diagnostic Codes for the Fuel Pressure Sensor {1718, 7620}
3126B Petroleum Engine Air Shutoff - Disassemble