Gear Pump (Torque Converter and Transmission) - Assemble
组装步骤
Show/hide table
| 需要的工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件名称 | 数量 |
| A | 1P-1857 | 挡圈钳 | 1 |
- 安装双头螺柱 (42) 。
Show/hide table
 | |
| 图 1 | g01186202 |
- 安装轴承 (41) 、盘 (40) 、盘 (37) 、密封 (38) 和密封 (39) 。
Show/hide table
 | |
| 图 2 | g01186201 |
- 将盘 (36) 装入壳体 (35) 。
Show/hide table
 | |
| 图 3 | g01186200 |
- 安装齿轮 (34) 、齿轮 (33) 和盘 (32) 。
Show/hide table
 | |
| 图 4 | g01186199 |
- 安装盘 (28) 、密封 (29) 、密封 (30) 和盘 (31) 。
Show/hide table
 | |
| 图 5 | g01186198 |
- 安装轴承 (27) 和 O 形密封圈 (26) 。
Show/hide table
 | |
| 图 6 | g01186196 |
- 安装 O 形密封圈 (25) 和壳体 (24) 。
Show/hide table
 | |
| 图 7 | g01186195 |
- 使用工具 (A) ，安装挡圈 (23) 。
- 安装 O 形密封圈 (21) 和联轴节 (22) 。
- 安装壳体 (20) 。
Show/hide table
 | |
| 图 8 | g01186191 |
- 安装轴承 (19) 。
Show/hide table
 | |
| 图 9 | g01186190 |
- 安装盘 (15) 、密封 (16) 、密封 (17) 和盘 (18) 。
- 安装盘 (14) 。
Show/hide table
 | |
| 图 10 | g01186189 |
- 安装齿轮 (13) 、齿轮 (12) 和盘 (11) 。
Show/hide table
 | |
| 图 11 | g01186188 |
- 安装盘 (7) 、密封 (8) 、密封 (9) 和盘 (10) 。
Show/hide table
 | |
| 图 12 | g01186186 |
- 安装轴承 (4) 和 O 形密封圈 (3) 。
Show/hide table
 | |
| 图 13 | g01186183 |
- 安装盖 (2) 和螺栓 (1) 。
Show/hide table
 | |
| 图 14 | g01186182 |
End By: 安装齿轮泵。 请参阅 解体和组装, "变速箱充油和扫油齿轮泵 - 安装"。
Caterpillar Information System:
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Disassemble
2005/08/15 Improved Spin-On Engine Oil Filters are Used {1308}
C6.6 Industrial Engine Crankcase Breather
C13 and C15 On-highway Engines Engine Speed - Test
C13 and C15 On-highway Engines Sensor Supply - Test
C13 and C15 On-highway Engines Shutdown Timer (PTO) - Test
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Install
3618 Engine Auxiliary Water Pump - Disassemble
TH48-E80 Oil/Gas Transmission Gear Pump (Torque Converter and Transmission) - Remove
C9 Generator Set Electronic Modular Control Panel 3 (EMCP 3)
C13 and C15 On-highway Engines Retarder - Test
Caterpillar 270 Air Compressor Rebuilt Air Compressor - Test
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Starting and Stopping
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Remove
C15 On-Highway Engine Fuel System - Prime
C-12 Generator Set Engine CID 0091 FMI 08 Throttle Position signal abnormal
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Install
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Disassemble
3618 Engine Auxiliary Water Pump - Assemble
3456 Generator Sets Starting the Engine - EMCP 3 (If Equipped)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Device Bus Network - Modbus Communications
3456 Generator Sets Manual Stop Procedure
TH48-E80 Oil/Gas Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Assemble
C6.6 Engines for Caterpillar Built Machines Crankshaft Seals