Steering Wheel Slip - Check
Before performing any procedures on the machine, read Service Manual Module, RENR3508, "Machine Preparation for Trouble Shooting" and understand the steps in Service Manual Module, RENR3508, "Machine Preparation for Trouble Shooting".
- Move the machine to a hard, dry surface.
- Engage the parking brake.
- Slightly raise the work tool off the ground.
- Release the service brakes.
- Run the engine at LOW idle.
- Make sure that the machine is in the straight ahead position.
- Slowly turn the steering wheel through one revolution so that there is a minimum of articulation.
- Slowly turn the steering wheel in the opposite direction so that there is a minimum of articulation.
- Slowly turn the steering wheel through one revolution to the left three times. Write down the needed time for each revolution of the steering wheel.
- Slowly turn the steering wheel through one revolution to the right three times. Write down the needed time for each revolution of the steering wheel.
- Add the three times for the left turns together.
- Add the times for the three right turns together.
If the total of the three left turns and the total for the three right turns are 60 seconds or more than 60 seconds then the slip is acceptable.
Caterpillar Information System:
3054 and 3056 Industrial and Generator Set Engines Turbocharger
C9 Engines for Caterpillar Built Machines Crankshaft - Install
D9R Track-Type Tractor Ether Starting Aid
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Analog Sensor Supply
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3524B Engines for Off-Highway Trucks Customer Parameters Worksheet
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System System Schematic
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Display Mode Selecting
988G Wheel Loader Engine Supplement Engine and Torque Converter - Remove
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
988G Wheel Loader Engine Supplement Alternator - Remove and Install
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
D10R Track-Type Tractor Machine Systems Air Conditioner Dryer - Remove and Install
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Digital Sensor Supply
SR4 and SR4B Electric Power Generation Rewind Data General Information
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Cat Data Link
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Connectors and Functions
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
980G Wheel Loader Hydraulic System Tilt Cylinder (High Lift)
515 Wheel Skidder and 525 Wheel Skidder Hydraulic and Steering System Control Valve (Hydraulic Retrieval Device)
3056 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove