Vibration Damper and Pulley - Remove
Removal Procedure
Start By:
- Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1) in order to remove vibration damper (2) .
Note: Do not use a puller tool to remove the crankshaft pulley from the crankshaft.
Show/hide table
Illustration 1 | g00891801 |
- Remove bolts (3) .
Show/hide table
Illustration 2 | g00891807 |
- Hold a wood block against the inner hub of the crankshaft pulley as shown. Strike the wood block with a hammer in order to loosen the split lock and the spacer.
Show/hide table
Illustration 3 | g00902007 |
- Carefully remove crankshaft pulley (8) . The weight of the crankshaft pulley is approximately 10 kg (22 lb).
- Remove thrust block (5) and O-ring seal (4) .
Show/hide table
Illustration 4 | g01513048 |
- Remove spacer (6) and split locks (7) from crankshaft pulley (8) .
Caterpillar Information System:
515 Wheel Skidder and 525 Wheel Skidder Hydraulic and Steering System Control Valve (Hydraulic Retrieval Device)
980G Wheel Loader Hydraulic System Tilt Cylinder (High Lift)
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Connectors and Functions
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Cat Data Link
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
SR4 and SR4B Electric Power Generation Rewind Data General Information
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Digital Sensor Supply
D10R Track-Type Tractor Machine Systems Air Conditioner Dryer - Remove and Install
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
924G and 924GZ Wheel Loaders Steering System Steering Wheel Slip - Check
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 05 Engine Cooling Fan Solenoid open circuit
924G and 924GZ Wheel Loaders Steering System Pump Flow - Test
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 06 Engine Cooling Fan Solenoid short to ground
3524B Engines for Off-Highway Trucks MID 036 - CID 0296 - FMI 09 Unable to communicate with Transmission ECM
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Truck Counter
D9R Track-Type Tractor Equalizer Bar End Pins - Measure
924G and 924GZ Wheel Loaders Steering System Hydraulic Oil Contamination - Test
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0526 - FMI 05 Turbo Wastegate Drive current low
924G and 924Gz Wheel Loaders Power Train Solenoid Valve (Transmission Clutch) - Test
515 Wheel Skidder and 525 Wheel Skidder Hydraulic and Steering System Solenoid Valve (Hydraulic Retrieval Device)
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust