Auxiliary Water Pump
Show/hide table
图 1 | g02837897 |
Show/hide table
技术规格 - 9Y-8909 辅助水泵总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 9X-4594 唇形密封 | 不要润滑密封唇。 |
4 | 1 | 166-4375 密封圈总成 | 按以下步骤安装密封总成:
只能使用干净的水或 P-80 润滑零件。 密封安装工具是更换密封总成的一部分。 1. 使用手压的密封安装工具将橡胶密封件 (2) 和陶瓷环 (3) 作为一个整体安装到泵壳体组件上。 2. 将弹簧从密封总成上拆下。 3. 使用手压的密封安装工具将密封总成安装到轴上,直到密封面轻轻接触。 4. 安装弹簧到密封总成上。 |
B | - | - | 叶轮和水泵盖之间的间隙为 |
C | - | - | 叶轮到泵壳体组件面的距离为 |
5 | 1 | 149-5462 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
6 | 1 | 212-8180 泵驱动轴组件 | 将叶轮压装至轴前,在轴上涂一薄层清洁的发动机机油进行润滑。 轴的端部必须与叶轮表面在 |
7 | 1 | 5H-6734 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
8 | 4 | 0S-1594 螺栓 | 拧紧至扭矩为 |
9 | 1 | 3D-2824 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
10 | 1 | 7G-8478 齿座 | 拧紧至扭矩为 |
11 | 3 | 9S-8752 全高螺母 | 拧紧至扭矩为 |
Caterpillar Information System:
Installation of Multishank Ripper 7PP{6310, 6315, 6316} Installation of Multishank Ripper 7PP{6310, 6315, 6316}
613C Series II Wheel Tractor-Scraper Cooling System Coolant (ELC) - Change
545 Wheel Skidder Engine Supplement Radiator - Remove and Install
963C Track-Type Loader Power Train Hydraulic Drive Pump - Install
545 Wheel Skidder Engine Supplement Turbocharger - Remove and Install
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic Tank Breaker Relief Valve - Clean
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors Starting Motor - Troubleshoot
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors Starting Motor - Disassemble
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors Starting Motor - Assemble
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors Normal Operation
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors No Load - Test
RA1.2, R1.4, R2.0, R2.2, R2.5, R2.7, R3.0, R4.5 and R5.5 Series Reduction Starting Motors Initial Troubleshooting Procedure
D6R Series II Track-Type Tractor Hydraulic System Steering Control Valve
992G, 992K, 994, 994D and 994F Wheel Loaders VIMS Loader Payload System Component Description
D6R Series II Track-Type Tractor Hydraulic System Counterbalance Valve
994D Wheel Loader Machine System Gear Pump (Pilot and Implement Oil Cooler) - Disassemble
615C Series II Wheel Tractor-Scraper Ejector Carrier Rollers - Check/Adjust
613C Series II Wheel Tractor-Scraper Cooling System Water Temperature Regulator - Replace
615C Series II Wheel Tractor-Scraper Ejector Carrier Rollers - Inspect/Pack/Replace
615C Series II Wheel Tractor-Scraper Ejector Guide Rollers - Check/Adjust
3034 Engine for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Air Inlet Elbow
613C Series II Wheel Tractor-Scraper Cutting Edges and End Bits - Inspect/Replace
615C Series II Wheel Tractor-Scraper Ejector Guide Rollers - Inspect/Replace