Cab - Install
Installation Procedure
- Install the washers in the original location on the mounting pads.
Show/hide table
Illustration 1 | g00725109 |
- Position cab (22) on the tractor with a hoist.
- Install horn button (21) .
Show/hide table
Illustration 2 | g00725108 |
- Install handle (20) on the hydraulic control rod.
- Install the plates and bolts (19) in order to hold the cab in place. Tighten the bolts to a torque of 475 ± 53 N·m (350 ± 39 lb ft).
Show/hide table
Illustration 3 | g00725106 |
- Connect wiring harness (18) .
- Connect wiring harness (16). Connect wire harness (15) to the circuit breaker box.
Show/hide table
Illustration 4 | g00726364 |
- Install hoses (17) to the washer fluid bottle.
- Install wire harness (14) .
Show/hide table
Illustration 5 | g00725103 |
- Connect rod end (13) .
Show/hide table
Illustration 6 | g00725102 |
- Connect wire harness (12) to the finger tip control.
Show/hide table
Illustration 7 | g00725100 |
- Connect wiring harness (11) .
Show/hide table
Illustration 8 | g00725099 |
- Install the air conditioner hose on the drain. Tighten hose clamp (10) .
Show/hide table
Illustration 9 | g00725097 |
- Pull the two heater hoses through the cab. Install the heater hoses on the heater core. Tighten two hose clamps (9) .
- Pull two hoses (8) through the cab. Connect the hoses to the refrigerant evaporator core.
- Install covers (5), (6) and (7) on the machine.
Show/hide table
Illustration 10 | g00725096 |
- Install covers (1), (2), (3) and (4) on the machine.
Show/hide table
Illustration 11 | g00725095 |
- Install the floorplate on the machine.
- Refer to the Service Manual, 7454 for the correct procedures for evacuating and charging the air conditioning system.
- Charge the air conditioner system. The correct charge is 2.5 kg (5.5 lb). Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
- Fill the implement hydraulic system. Refer to the appropriate Operation and Maintenance Manual for the correct procedure.
End By:
- Install the hood. Refer to Disassembly and AssemblySENR8483, "Hood - Install".
- Install the rollover protective structure (ROPS). Refer to Disassembly and Assembly, "Rollover Protective Structure - Remove and Install" for the machine that is being serviced.
Caterpillar Information System:
D8R Track-Type Tractor Battery - Inspect
D6M Track-Type Tractor Machine Systems Bulldozer Tilt Cylinder - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Tilt Cylinder - Install
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder Mounts - Remove and Install
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Lift Cylinder - Install
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Remove
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Install
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Disassemble
D6M Track-Type Tractor Machine Systems Bulldozer Control Valve - Assemble
D6M Track-Type Tractor Machine Systems Bulldozer C-Frame - Remove and Install
D6M Track-Type Tractor Machine Systems Bulldozer Angle Cylinder - Remove
D6M Track-Type Tractor Machine Systems Cab - Remove
D6M Track-Type Tractor Machine Systems Implement Pump - Assemble
D6M Track-Type Tractor Machine Systems Implement Pump - Disassemble
D6M Track-Type Tractor Machine Systems Implement Pump - Install
D6M Track-Type Tractor Machine Systems Implement Pump - Remove
D6M Track-Type Tractor Machine Systems Fuel Tank - Install
D6M Track-Type Tractor Machine Systems Fuel Tank - Remove
637E Series II Wheel Tractor-Scrapers Bail Control
D6M Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Assemble
D6M Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Disassemble
D6M Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Install
D6M Track-Type Tractor Machine Systems Governor Control Linkage and Decelerator - Remove