Turbocharger - Install - Single Turbocharger
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 5P-3931 | 防粘结剂 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将密封垫安置在排气歧管上。
- 将适当起吊设备连在涡轮增压器 (1) 上。 涡轮增压器 (1) 的重量约为
23 kg (50 lb) 。 将涡轮增压器 (1) 安装到排气歧管上。注: 使用后请丢弃锁紧螺母。 安装时请使用新的锁紧螺母。
- 将工具 (A) 涂抹到排气歧管螺柱的螺纹上,然后手动拧紧锁紧螺母 (5)。
- 将整体式密封定位到涡轮增压器 (1) 上,然后连接排油管组件 (6)。
- 将密封垫定位到涡轮增压器 (1) 上,然后将输油管组件 (3) 连接到涡轮增压器 (1) 上。
- 将密封垫定位到涡轮增压器 (1) 上,然后连接冷却器软管组件 (2)。
- 将密封垫定位到涡轮增压器 (1) 上,然后连接冷却器软管组件 (4)。
- 适度松开 V 形带箍上的螺母以使涡轮壳体可以旋转。 连接涡轮壳体上的排气管。 拧紧 V 形带箍上的螺母至扭矩为
14 ± 1 N·m (124 ± 9 lb in) 。 用软锤在 V 形带箍的直径四周轻轻敲打。 拧紧螺母至扭矩为14 ± 1 N·m (124 ± 9 lb in) 。 - 拧紧锁紧螺母 (5) 至扭矩为
55 ± 5 N·m (41 ± 4 lb ft) 。 - 加注冷却系统。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 1 | g01095550 |
Caterpillar Information System:
C15 and C18 Industrial Engines Turbocharger - Remove - Single Turbocharger
3500B and 3500C Generator Set Engines Fuel System Operation
C15 and C18 Industrial Engines Exhaust Manifold - Remove and Install - Dual Turbochargers
2004/08/01 New Circuit Breakers Are Now Being Used {4461}
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Telemetry Parameters
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Troubleshooting
C15 and C18 Industrial Engines Exhaust Manifold - Remove and Install - Single Turbocharger
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies User Interface
3306C Engines for Caterpillar Built Machines Charging System - Test
C9 Engines for Caterpillar Built Machines Engine Design
C9 Engines for Caterpillar Built Machines Engine Design
C15 and C18 Petroleum Engines Engine Design
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Valve Mechanism
3406E and 3456 Generator Set Engines Fuel System Pressure - Test
3516B Generator Set Engines with Dynamic Gas Blending Valve Lash - Adjust
G3520B Industrial Engine MID 036 - CID 0102 - FMI 03 Boost Pressure Sensor short to +batt
2006/03/06 Insulation on Exhaust Components {1000}
G3408 and G3412 Engines Carburetor Control Linkage
G3520B Industrial Engine Troubleshooting Data Sheet
3412E, C30 and C32 Marine Engines Cylinder Liner - Install
G3520B Industrial Engine Air/Fuel Ratio Control
G3520B Industrial Engine Low Power/Poor or No Response to Throttle
G3520B Industrial Engine MID 036 - CID 0102 - FMI 08 Boost Pressure Sensor noisy signal
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Remove