Valve Lash - Adjust
Show/hide table
气门间隙设定:发动机停机 | |
---|---|
气门 | 规格尺寸 |
进口 | |
排气 | |
使用此步骤调整气门间隙。
Show/hide table
所需工具 | ||
---|---|---|
零件号 | 零件名称 | 数量 |
147-2060 | 扳手 | 1 |
147-2059 | 扭矩扳手 | 1 |
148-7211 | 气门桥螺母套筒 | 1 |
145-5191 | 仪表支撑 | 1 |
147-2056 | 千分表 | 1 |
147-5536 | 千分表触针 | 1 |
147-2057 | 千分表触针 | 1 |
147-2058 | 千分表接长杆 | 1 |
147-5537 | 千分表(未显示) | 1 |
注: 145-5191 仪表支撑 (4)、 147-2057 千分表触针 (7)、 147-2058 千分表接长杆 (8) 和 147-5536 千分表触针 (6) 均包括在 147-5482 气门间隙仪表总成中。
注: 147-2056 千分表或 147-5537 千分表(公制,未显示)可与 147-5482 气门间隙仪表总成一起使用。
- 确保第1缸活塞处于上止点位置。 请参阅测试和调整, "查找 1 号活塞上止点位置"。
- 1 号活塞应处于正确冲程的上止点位置。 根据图表对气门进行调整:请参阅测试和调整, "喷油器调整和气门间隙设置曲轴位置"。
注: 在进行任何调整之前,先在调节螺钉的顶部敲击每一个摇臂。 使用软木锤。 确保挺杆滚轮落靠在凸轮轴的基圆上。
- 安装 145-5191 仪表支撑 (1)。 使用 147-2056 千分表或使用 147-5537 千分表。 使用 147-2057 千分表触针 (2)。 将此工具安装到后螺栓孔上。 后螺栓孔位于气门盖底座上。
Show/hide table
图 2 g00286366 (3) 147-2060 扳手
(4) 147-2059 扭矩扳手Show/hide table图 3 g00286367 (3) 147-2060 扳手
(4) 147-2059 扭矩扳手 - 将摇臂组件上下移动。 多次移动摇臂组件。 清除油膜以便在千分表上调得真正的零位。 使用 147-2060 扳手 (3) 和使用 147-2059 扭矩扳手 (4)。 在摇臂螺母上安装套筒扳手和扭矩扳手。 在摇臂组件的前端处向上施加压力。 把千分表调零。 扭矩扳手 (4) 的重量使得气门间隙能够被读取。 不要在扭矩扳手上施加任何压力。
- 松开锁紧螺母。 锁紧螺母位于推杆调整螺钉上。 转动此调整螺钉直到气门间隙符合技术规格。 拧紧调整螺钉的螺母至扭矩为
70 ± 15 N·m (50 ± 11 lb ft) 。 147-2059 扭矩扳手已被预设为所需扭矩。 再次检查调整。
Show/hide table
图 1 | g00286365 |
(1) 145-5191 仪表支撑
(2) 147-2057 千分表触针 |
Caterpillar Information System:
3406E and 3456 Generator Set Engines Fuel System Pressure - Test
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Valve Mechanism
C15 and C18 Industrial Engines Turbocharger - Install - Single Turbocharger
C15 and C18 Industrial Engines Turbocharger - Remove - Single Turbocharger
3500B and 3500C Generator Set Engines Fuel System Operation
C15 and C18 Industrial Engines Exhaust Manifold - Remove and Install - Dual Turbochargers
2004/08/01 New Circuit Breakers Are Now Being Used {4461}
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Telemetry Parameters
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Troubleshooting
C15 and C18 Industrial Engines Exhaust Manifold - Remove and Install - Single Turbocharger
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies User Interface
3306C Engines for Caterpillar Built Machines Charging System - Test
G3520B Industrial Engine MID 036 - CID 0102 - FMI 03 Boost Pressure Sensor short to +batt
2006/03/06 Insulation on Exhaust Components {1000}
G3408 and G3412 Engines Carburetor Control Linkage
G3520B Industrial Engine Troubleshooting Data Sheet
3412E, C30 and C32 Marine Engines Cylinder Liner - Install
G3520B Industrial Engine Air/Fuel Ratio Control
G3520B Industrial Engine Low Power/Poor or No Response to Throttle
G3520B Industrial Engine MID 036 - CID 0102 - FMI 08 Boost Pressure Sensor noisy signal
3412E, C30 and C32 Marine Engines Pistons and Connecting Rods - Remove
2004/08/01 A New Head Gasket is Now Available as Service Replacement {1124}
G3408 and G3412 Engines Carburetor Control Linkage
3412E, C30 and C32 Marine Engines Connecting Rod Bearings - Remove