Ride Control Valve - Remove
拆卸步骤
开始:
- 连接转向机架锁。 请参考拆解和组装, "转向机架锁 - 分离和连接"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
 |
热油和热的部件可能会导致人员受伤。 请勿让热的液压油或热的零部件与皮肤接触。 |
注: 在所有管路、软管、导线和管子上做出识别标记以便安装。 插接所有管路、软管、导线和管子。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将机具液压油箱中的机油排入适当的容器内。 油箱容量为 326 L (85 US gal)。
- 拆下螺栓 (3) ，以便将管组件 (2) 从行驶控制阀 (1) 上断开。 拆下卡箍 (4) 。
Show/hide table
 | |
| 图 1 | g00419568 |
注: 行驶控制阀位于前装载机机架上上部铰接附近。
- 将管组件 (2) 的另一端从连接处断开。 拆下卡箍 (5) 和卡箍组件 (6) 。
Show/hide table
 | |
| 图 2 | g00420117 |
- 将电气接头 (8) 、软管组件 (7) 和软管组件 (9) 从行驶控制阀 (1) 上断开。
Show/hide table
 | |
| 图 3 | g00420182 |
- 拆下螺栓 (11) 以便断开其余两根软管组件 (10) 。 拆下行驶控制阀 (1) 。
Show/hide table
 | |
| 图 4 | g00420191 |
Caterpillar Information System:
613C Series II Wheel Tractor-Scraper Machine Systems Vane Motor (Elevator) - Disassemble
D6G Track-Type Tractor Power Train Final Drive Gear, Idler Pinion and Bearings - Remove
992G Wheel Loader Machine Systems Ride Control Valve - Disassemble
3306B Industrial Engine Air Tank Moisture and Sediment - Drain - If Equipped
D6G Track-Type Tractor Power Train Final Drive Case - Remove and Install
966G Wheel Loader and 972G Wheel Loader Power Train Transmission Planetary
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Steering Neutralizer Valve - Check and Adjust
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Pilot Valve (Steering) Supply Pressure - Test and Adjust
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Steering Pilot System Pressure - Test
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Relief Valve (Pump Backup) - Test and Adjust - Command Control Steering
613C Series II Wheel Tractor-Scraper Machine Systems Floor Dump Arm - Remove and Install
615C Series II Wheel Tractor-Scraper Machine Systems Pilot Control Valve (Elevator) - Disassemble
966G Wheel Loader and 972G Wheel Loader Power Train Output Transfer Gears
992G Wheel Loader and 854G Wheel Dozer Steering System Steering Neutralizer Valve - Check and Adjust
994D Wheel Loader Power Train Rollover Protective Structure (ROPS)
613C Series II Wheel Tractor-Scraper Machine Systems Vane Motor (Elevator) - Assemble
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Leakage - Test
902 and 906 Compact Wheel Loaders Hydraulic System Lift Cylinder
Repair of Boom and Bucket Stop Alignment{6107, 6501} Repair of Boom and Bucket Stop Alignment{6107, 6501}
613C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Disassemble
615C Series II Wheel Tractor-Scraper Machine Systems Pilot Control Valve (Elevator) - Assemble
994D Wheel Loader Power Train Rim Mounting
992G Wheel Loader Machine Systems Ride Control Valve - Install
613C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Remove