Crankshaft Gear - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 8B-7551 | Bearing Puller | 1 |
| 8B-7549 | Puller Leg | 2 | |
| 3H-0465 | Push-Puller Plate | 4 | |
| 6B-6682 | Full Nut | 2 | |
| 8B-7560 | Step Plate | 1 | |
| 1P-0820 | Hydraulic Puller | 1 | |
| 9U-6600 | Hand Hydraulic Pump | 1 | |
Start By:
- Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove crankshaft gear (1) from crankshaft (2) .
Show/hide table
 | |
| Illustration 1 | g01080427 |
- Remove the woodruff key (not shown) from the crankshaft.
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position the woodruff key (not shown) in the crankshaft.
- Raise the temperature of crankshaft gear (1). Install crankshaft gear (1) on crankshaft (2) .
Show/hide table
 | |
| Illustration 2 | g01080425 |
Show/hide table
 |
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
 |
End By: Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Caterpillar Information System:
G3500B Engines Auxiliary Water Pump
G3500 A3 Engines Engine Shutdown
C-10 and C-15 Petroleum Engines Intermittent Engine Shutdown
2004/07/01 Internal Components for Remanufactured Injectors are Now Coated for Increased Service Life {1290}
3126B Petroleum Engine Exhaust Temperature Is Too High
C13, C15, and C18 Generator Set Engines Excessive Black Smoke
C27 and C32 Industrial and Petroleum Engines Engine Will Not Crank
3126B Petroleum Engine Engine Stalls at Low RPM
C-10 and C-15 Petroleum Engines Engine Misfires, Runs Rough or Is Unstable
C-10 and C-15 Petroleum Engines Engine Cranks but Will Not Start
3126B Petroleum Engine Electronic Service Tool Will Not Communicate with ECM
C7 Marine Engines Pistons and Connecting Rods - Install
C7 Marine Engines Electronic Control Module - Remove and Install
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Modem
C7 Marine Engines Alternator - Remove and Install
C7 Marine Engines Electric Starting Motor - Remove and Install
3126B Petroleum Engine E025 High Inlet Air Temperature Derate
3126B Petroleum Engine E027 High Inlet Air Temperature Warning
3126B Petroleum Engine E039 Low Engine Oil Pressure Derate
3126B Petroleum Engine E040 Low Engine Oil Pressure Shutdown
C15 On-highway Engines Engine Control Module - Remove and Install
C-10 and C-15 Petroleum Engines E054 High Fuel Temperature Derate
C-10 and C-15 Petroleum Engines E055 High Fuel Temperature Shutdown
C-10 and C-15 Petroleum Engines E056 High Fuel Temperature Warning