Coolant Temperature Sensor - Remove and Install
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 冷却液温度传感器位于水温调节器壳体内。
- 将冷却系统的冷却液中排入适当的容器至液位低于冷却液温度调节器,以便保存或废弃。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 1 g01068156 - 断开线束组件 (2)。
- 将冷却液温度调节器 (1) 从水温调节器壳体上拆下。
- 将 O 形密封圈从冷却液温度调节器上拆下。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将一个新的 O 形密封圈安装在冷却液温度调节器上。
- 安装冷却液温度调节器 (1) 并拧紧至扭矩为
20 ± 3 N·m (15 ± 2 lb ft) 。 - 连接线束组件 (2)。
- 向冷却系统加注冷却液。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 2 | g01068156 |
Caterpillar Information System:
3406E and 3456 Generator Set Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
C15 and C18 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
C15 and C18 Generator Set Engines Atmospheric Pressure Sensor - Remove and Install
3406E and 3456 Generator Set Engines Emergency Stop Switch Circuit - Test
C15 Petroleum Engines Pump Drive - Install
C15 Petroleum Engines Pump Drive - Remove
Machining of The Cylinder Block to Convert from Wet Cylinder Liners to Dry Cylinders Liners{1201} Machining of The Cylinder Block to Convert from Wet Cylinder Liners to Dry Cylinders Liners{1201}
3508, 3512, and 3516 Generator Sets Refill Capacities and Recommendations
3406E and 3456 Generator Set Engines Air Shutoff System - Test
Product Link - PL102C Reports and Messages Not Available
C15 Engine Reference Material
C11 and C13 Petroleum Engines Plate Locations and Film Locations
3406E and 3456 Generator Set Engines Overspeed Verify Switch Circuit - Test
2004/04/01 The Power Steering Pump May not be Seated Properly {1151, 4306}
C15 and C18 Generator Set Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C15 and C18 Industrial Engines Crankshaft Position Sensor - Remove and Install
Operating Controls For The Multiline-2 Controller{7451} Operating Controls For The Multiline-2 Controller{7451}
C15 and C18 Industrial Engines Camshaft Position Sensor - Remove and Install
3406E and 3456 Generator Set Engines Engine Sensor Open/Short Circuit - Test
C-15 Petroleum Engine Fuel Temperature Sensor - Remove and Install
3406E and 3456 Generator Set Engines CID 0535 FMI 08 Exhaust Temperature Sensor noisy signal
C-15 Petroleum Engine Fuel Pressure Sensor - Remove and Install
C15 and C18 Generator Set Engines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines CID 0446 FMI 05 Air Shutoff Relay open