Cylinder Head - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 6V-4876     | 润滑剂     | 1     |
B     | 8T-2998     | 润滑剂     | 1     |
C     | 9S-3263     | 螺纹锁固胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将 O 形密封圈 (21) 安装到缸体中的定位销上。
Show/hide table
图 1 | g01117797 |
- 将隔板密封垫 (23) 安装到缸体上。
- 安装密封 (24) 和密封 (22) 。
- 安装隔板 (20) 。
- 将缸盖密封垫 (19) 安装到隔板上。
- 将适当的起吊设备连接到缸盖 (16) 。 缸盖的重量约为 235 kg (518 lb)。
Show/hide table
图 2 | g01116398 |
- 小心地将缸盖 (16) 安装到缸体中的定位销上。
- 将工具 (A) 涂覆到缸盖螺栓 (15) 的螺栓螺纹上和垫圈的两侧。 使用下述顺序安装并拧紧螺栓:
- 按照数字顺序依次拧紧螺栓 1 到 26 至扭矩为 270 ± 15 N·m (200 ± 11 lb ft)。
- 按照数字顺序依次拧紧螺栓 1 到 26 至扭矩为 450 ± 15 N·m (330 ± 11 lb ft)。
- 按照数字顺序,再次依次拧紧螺栓 1 到 26 至扭矩为 450 ± 15 N·m (330 ± 11 lb ft)。
Show/hide table
图 3 | g01020264 |
注: 下列螺栓的长度为 216 mm (8.5 in):11, 12, 13, 14, 16, 18, 20, 22, 24 和 26。 其余螺栓的长度为 194 mm (7.6 in)。
- 安装扎带 (18) 。
- 安装水温调节器壳体 (17) 。
- 连接进气温度传感器 (14) 。
Show/hide table
图 4 | g01117768 |
- 连接增压压力传感器 (13) 。
- 将支架安置在缸盖上,安装螺栓 (7) 。
- 将呼吸器管放置到缸盖上,然后安装螺栓 (11) 。 拧紧螺栓至扭矩为 10 ± 3 N·m (89 ± 27 lb in)。
- 将燃油滤清器底座 (9) 放置到缸盖上,然后安装螺栓 (10) 。
- 连接软管组件 (12) 。
- 连接软管组件 (8) 。
- 将 O 形密封圈 (5) 和 O 形密封圈 (6) 安装在密封盘 (3) 上。 使用以 50/50 比例混合的工具 (B) 与清洁发动机机油润滑 O 形密封圈 (6) 。
Show/hide table
图 5 | g01056684 |
- 安装适配器组件 (4) 和密封盘 (3) 。 确保适配器组件 (4) 中的定位销与凸轮轴中的孔啮合。
Show/hide table
图 6 | g01116390 |
Show/hide table
图 7 | g01056681 |
- 安装止推盘 (1) 。 将工具 (C) 涂抹在螺栓 (2) 上。 固定止推盘到位并安装螺栓 (2) 。 均匀地拧紧螺栓 (2) ,直到密封盘 (3) 和 O 形密封圈紧贴落座在缸盖上。
注: 确保 O 形密封圈保持在密封盘 (3) 的凹槽中。
- 加注冷却系统。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
End By:
- 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
- 安装气门机构罩盖底座。 请参阅 拆解和组装, "气门机构罩盖底座 - 拆卸和安装"。
- 安装电子单体喷油器。 请参阅 拆解和组装, "电子单体喷油器 - 安装"。
- 安装凸轮轴齿轮。 请参阅 拆解和组装, "凸轮轴齿轮 - 拆卸和安装"。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Cylinder Head - Remove
3126B Marine Engines Low Power/Poor or No Response to Throttle
C-15 Petroleum Engine Refill Capacities and Recommendations
C7 Marine Engine Engine Monitoring System (EMS)
G3300 Engines Refill Capacities and Recommendations
C32 Petroleum Engines Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
C7 Marine Engine Flywheel
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C18 Generator set and C18 Marine Engines Pistons and Connecting Rods - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Remove
C7 Marine Engine Reference Material
3126B Petroleum Engine Battery Electrolyte Level - Check
3512B Petroleum Engine Battery or Battery Cable - Disconnect
3126B Petroleum Engine Belt - Inspect
3408B and 3408C Industrial and Marine Engines Turbocharger
C-10 Petroleum Engine Engine Oil and Filter - Change
C7 Marine Engine Cylinder Block Cover Group
G3600 Engines Additional Messages
C11 and C13 Petroleum Engines Starting Motor - Inspect - If Equipped
2004/04/01 Engine Harness Assembly (Bypass) Flashes Messenger When Communication Through the Service Connector is Not Possible {0779, 0781}
C7 Marine Engine Electronic Unit Injector
C-15 Petroleum Engine Plate Locations and Film Locations
C7 Marine Engine Sensors and Electrical Components