Cylinder Head - Remove
开始:
- 卸下凸轮轴齿轮。 请参阅拆解和组装 , "凸轮轴齿轮 - 拆卸和安装" 。
- 拆卸电子单体喷油器。 请参阅拆解和组装 , "电子单体喷油器 - 拆卸"。
- 拆卸气门机构盖底座。 请参阅拆解和组装 , "气门机构盖底座 - 拆卸和安装" 。
- 拆卸涡轮增压器。 请参阅拆解和组装 , "涡轮增压器 - 拆卸"。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
- 排空冷却系统。 请参考操作和保养手册 , "冷却系统冷却液 - 更换"。
Show/hide table
图 1 g01056681 - 卸下螺栓 (2) 和止推盘 ( 1)。
Show/hide table
图 2 g01116390 - 卸下密封盘 (3) 和接头组件 ( 4)。
Show/hide table
图 3 g01056684 - 从密封盘 (3) 上卸下 O 形密封圈 (5) 和 O 形密封圈 (6)。
Show/hide table
图 4 g01117768 - 断开软管组件 (8)。
- 断开软管组件 (12)。
- 拆卸螺栓 (10)。 将燃油滤清器底座 ( 9) 移到旁边。
- 从缸盖上卸下螺栓 ( 11) 和呼吸器管。
- 卸下螺栓 (7),然后从缸盖上卸下支架。
- 断开增压压力传感器 ( 13)。
- 断开进气温度传感器 ( 14)。
Show/hide table
图 5 g01116398 - 卸下水温调节器壳体 ( 17)。
- 卸下绑带 (18)。
- 将适当的起吊设备接连在缸盖 ( 16) 上。 缸盖的重量约为
235 kg (518 lb) 。 - 卸下缸盖螺栓 (15)。
- 小心地卸下缸盖 ( 16)。
Show/hide table
图 6 g01117797 - 卸下缸垫 (19)。
- 卸下隔盘 (20)。
- 卸下密封 (24) 和密封 ( 22)。
- 卸下隔盘密封垫 ( 23)。
- 从缸体中的定位销上卸下 O 形密封圈 (21)。
Caterpillar Information System:
3126B Marine Engines Low Power/Poor or No Response to Throttle
C-15 Petroleum Engine Refill Capacities and Recommendations
C7 Marine Engine Engine Monitoring System (EMS)
G3300 Engines Refill Capacities and Recommendations
C32 Petroleum Engines Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
C7 Marine Engine Flywheel
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C18 Generator set and C18 Marine Engines Pistons and Connecting Rods - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Remove
C7 Marine Engine Reference Material
C7 Marine Engine Engine Oil Filter Base
C15 and C18 Engines for Caterpillar Built Machines Cylinder Head - Install
3126B Petroleum Engine Battery Electrolyte Level - Check
3512B Petroleum Engine Battery or Battery Cable - Disconnect
3126B Petroleum Engine Belt - Inspect
3408B and 3408C Industrial and Marine Engines Turbocharger
C-10 Petroleum Engine Engine Oil and Filter - Change
C7 Marine Engine Cylinder Block Cover Group
G3600 Engines Additional Messages
C11 and C13 Petroleum Engines Starting Motor - Inspect - If Equipped
2004/04/01 Engine Harness Assembly (Bypass) Flashes Messenger When Communication Through the Service Connector is Not Possible {0779, 0781}
C7 Marine Engine Electronic Unit Injector
C-15 Petroleum Engine Plate Locations and Film Locations