Pistons and Connecting Rods - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 6V-6192     | 钳     | 1     |
B     | 7B-7974     | 活塞环扩张器总成     | 1     |
C     | 5P-8639     | 液压 (连杆轴承)     | 1     |
8F-0024 | 软管组件     | 1     | |
1P-2375 | 连接器     | 1     | |
1P-2376 | 连接器     | 1     | |
5P-8651 | 隔套     | 1     | |
5P-8649 | 适配器     | 1     | |
5P-8650 | 衬套接头     | 1     | |
9U-6600 | 液压泵     | 1     |
注: 从发动机上拆下之前,活塞和连杆组件上已经作了标记。 所有的部件必须重新组装起来。 所有部件必须安装回它们在发动机中原来的位置。 请勿互换任何部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 沿长度 (Y) 加热连杆 (6) 。
(Y) 加热连杆的最大长度 ... 93 mm (3.7 in)
Show/hide table
图 1 | g01017742 |
Show/hide table
图 2 | g01018268 |
Show/hide table
注意 |
---|
在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。 |
- 让连杆和轴承冷却到室温。
- 用工具 (C) 来拆掉旧轴承,同时换上新轴承 (7) 。 工具 (C) 的适配器应与连杆 (6) 的表面充分接触。
注: 调整轴承接头两端的方向在位置 (X) ± 5 度范围内。
- 用销膛磨机加工轴承孔 (7) ,以修正直径。
轴承孔直径 ... 60.035 ± 0.008 mm (2.3636 ± 0.0003 in)
- 将控油环的弹簧安置在活塞体组件中的油环槽中。
Show/hide table
图 3 | g01056145 |
- 将控油环 (3) 安置在弹簧的上方。 安置控油环,使其开口与弹簧接头成 180 度。 使用工具 (B) 将控油环安装在活塞上。
- 使用工具 (B) 安装中间活塞环 (2) ,使有 "UP-2" 标记的一侧朝向活塞顶部。
- 使用工具 (B) 安装顶部活塞环 (1) ,使有 "UP-1" 标记的一侧朝向活塞顶部。
- 安置活塞环 (1) 、 (2) 和 (3) ,使其开口之间互成120度。
- 检查活塞环 (1) 、 (2) 和 (3) 底部之间的间隙。 请参考技术规格, "活塞和活塞环"。
- 将活塞体组件 (4) 放置到连杆 (6) 上。 将清洁的发动机机油涂覆到连杆销 (8) 上,然后安装连杆销。 使用工具 (A) 安装销固定器 (5) 。
- 将上连杆轴承 (9) 安装到连杆 (6) 中。
注: 确保轴承锁舌位于连杆的槽口中。
- 将下连杆轴承 (10) 安装到连杆盖 (11) 中。
注: 确保轴承锁舌位于连杆盖的槽口中。
- 确保连杆盖中已安装了定位销。
End By: 安装活塞和连杆。 请参阅 拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C18 Generator set and C18 Marine Engines Pistons and Connecting Rods - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Remove
C7 Marine Engine Reference Material
C7 Marine Engine Engine Oil Filter Base
C-15 Petroleum Engine Engine Description
3126B Petroleum Engine Welding on Engines with Electronic Controls
C15 Petroleum Engines Engine Electronics
3126B Petroleum Engine Fire Prevention and Explosion Prevention
3126B Petroleum Engine General Hazard Information
C-15 Petroleum Engine Flywheel
C15 Petroleum Engines Safety Messages
C7 Marine Engine Flywheel
C32 Petroleum Engines Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
G3300 Engines Refill Capacities and Recommendations
C7 Marine Engine Engine Monitoring System (EMS)
C-15 Petroleum Engine Refill Capacities and Recommendations
3126B Marine Engines Low Power/Poor or No Response to Throttle
C15 and C18 Engines for Caterpillar Built Machines Cylinder Head - Remove
C15 and C18 Engines for Caterpillar Built Machines Cylinder Head - Install
3126B Petroleum Engine Battery Electrolyte Level - Check
3512B Petroleum Engine Battery or Battery Cable - Disconnect
3126B Petroleum Engine Belt - Inspect
3408B and 3408C Industrial and Marine Engines Turbocharger