Engine Support (Front) - Remove and Install
Show/hide table
需要的工具 | |||
---|---|---|---|
工具 | 零件号 | 零件名称 | 数量 |
A | - | 导向螺柱 (1/2 - 13 UNC X 6 in) |
2 |
开始:
- 拆卸减振器和皮带轮。 请参阅拆解和组装 , "减振器和皮带轮 - 拆卸和安装" 。
- 支撑发动机。
Show/hide table
图 1 g01044587 - 拆卸螺栓 (1) 并安装工具 ( A)。 卸下其余的螺栓。
- 从缸体上卸下发动机支承 ( 2)。 发动机支承 (2) 的重量约为
24 kg (53 lb) 。
Show/hide table
需要的工具 | |||
---|---|---|---|
工具 | 零件号 | 零件名称 | 数量 |
A | - | 导向螺柱 (1/2 - 13 UNC X 6 in) |
2 |
- 将发动机支承 (2) 安置在工具 ( A) 上。 发动机支承 ( 2) 的重量约为
24 kg (53 lb) 。 - 安装螺栓 (1),用手拧紧。 拆卸工具 (A),安装其余的螺栓。
Show/hide table
图 3 g01044639 - 按数字顺序将螺栓拧紧至扭矩为
105 ± 20 N·m (77 ± 15 lb ft) 。
Show/hide table
图 2 | g01044587 |
结束:
- 安装减振器和皮带轮。 请参阅拆解和组装 , "减振器和皮带轮 - 拆卸和安装" 。
Caterpillar Information System:
C18 Marine Auxiliary Engines Switch Circuits - Test
C18 Marine Auxiliary Engines Analog Sensor Supply Circuit - Test
2004/02/01 Improved Software Has Been Released For The C7 On-Highway Truck Engine {7620}
G3500 Engines Detonation Retard and Detonation Shutdown
Troubleshooting for Marine Engine Electronic Displays Messenger - Test
C9 Marine Auxiliary and Marine Generator Set Engines Injection Actuation Pressure Control Valve Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Equipped with Rear Power Take-Off
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove
2003/12/01 Parts List for Prelube Pump Group Kits {1319}
Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307} Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307}
C18 Marine Generator Set Engines Engine Temperature Sensor Open or Short Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers ECM Will Not Communicate with Other Systems or Display Modules
2004/01/26 A New Spring for the Oil Filter Bypass Valve and for the Oil Cooler Bypass Valve is Now in Production {1306, 1314, 1318, 1378}
G3500 Engines Diagnostic Reset Switch
C18 Marine Auxiliary Engines Engine Pressure Sensor Open or Short Circuit - Test
2004/05/03 New Hydraulic Hose Assembly Machine Integrates Crimputer II with Radial Crimping Technology {0738}
2006/06/26 Some Pistons and Cylinder Packs are Cancelled and Replaced {1214}
2004/01/01 A Special Instruction, REHS2060 , "Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump" is Available {1307, 1714}
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Intermittent Engine Shutdown
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C9 Marine Auxiliary and Marine Generator Set Engines Low Power/Poor or No Response to Throttle