Vibration Damper and Pulley - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 (5/8 - 18 NF x 7 in) |
1 |
B | 138-7575 | 连杆支架 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下一颗螺栓 (4)。 将工具 (B) 和适当的起吊设备安装到减振器 (3) 和曲轴皮带轮 (1) 上。 减振器 (3) 和曲轴皮带轮 (1) 的重量约为
57 kg (125 lb) 。 - 拆下一条螺栓 (2)。 安装工具 (A)。
- 拆下其余的螺栓 (2)。 从曲轴上卸下减振器 (3) 和曲轴皮带轮 (1)。
- 卸下螺栓 (4)。 拆下隔套 (5)。 从曲轴皮带轮 (1) 上卸下减振器 (3)。 减振器 (3) 的重量约为
34 kg (75 lb) 。
Show/hide table
图 1 | g01044774 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 (5/8 - 18 NF x 7 in) |
1 |
B | 138-7575 | 连杆支架 | 1 |
C | 4C-5592 | 防粘结剂 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
彻底接触粘滞减振器是否有漏油或外壳凹陷(损坏)的迹象。 这两个情况中的任何一个都可能导致重块与外壳相接触。 这样会影响粘滞减振器的操作。 |
- 将减振器 (3) 安置在曲轴皮带轮 (1) 上。 减振器 (3) 的重量约为
34 kg (75 lb) 。 - 将隔套 (5) 安装在减振器上。 安装螺栓 (4) 并拧紧螺栓至扭矩为
135 ± 20 N·m (100 ± 15 lb ft) 。 - 将工具 (B) 和适当的起吊设备安装在减振器 (3) 和曲轴皮带轮 (1) 上。 减振器 (3) 和曲轴皮带轮 (1) 的重量约为
57 kg (125 lb) 。 将减振器和曲轴皮带轮安装在工具 (A) 上。 - 将工具 (C) 涂抹在螺栓 (2) 上。 安装螺栓。 拆下工具 (A) 后安装其余螺栓。 拧紧螺栓至扭矩为
215 ± 40 N·m (159 ± 30 lb ft) 。
Show/hide table
图 2 | g01044774 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 (5/8 - 18 NF x 7 in) |
1 |
- 拆下皮带轮 (1) 和皮带。 请参考皮带预张紧器 - 拆卸和安装。
Show/hide table
图 4 g03181936 - 拆下一条螺栓 (2)。 将工具 (A) 和适当的提升设备安装到减振器 (4) 上。 拆下螺栓 (2)、隔套 (3) 和减振器 (4)。 减振器 (4) 的重量约为
13.7 kg (30.22 lb) 。
Show/hide table
图 3 | g03181887 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 (5/8 - 18 NF x 7 in) |
1 |
C | 4C-5592 | 防粘结剂 | 1 |
- 将工具 (A) 安装在曲轴中。 将减振器 (4) 安置在工具 (A) 上。 减振器 (3) 的重量约为
14 kg (30 lb) 。 - 将工具 (C) 涂抹到螺栓 (2) 上。 安装隔套 (3) 和螺栓 (2)。
Show/hide table
图 6 g03181887 - 安装皮带轮 (1)。 请参考皮带预张紧器 - 拆卸和安装。
Show/hide table
图 5 | g03181936 |
Caterpillar Information System:
C18 Marine Generator Set Engines Engine Temperature Sensor Open or Short Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Engine Support (Front) - Remove and Install
C18 Marine Auxiliary Engines Switch Circuits - Test
C18 Marine Auxiliary Engines Analog Sensor Supply Circuit - Test
2004/02/01 Improved Software Has Been Released For The C7 On-Highway Truck Engine {7620}
G3500 Engines Detonation Retard and Detonation Shutdown
Troubleshooting for Marine Engine Electronic Displays Messenger - Test
C9 Marine Auxiliary and Marine Generator Set Engines Injection Actuation Pressure Control Valve Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Equipped with Rear Power Take-Off
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers ECM Will Not Communicate with Other Systems or Display Modules
2004/01/26 A New Spring for the Oil Filter Bypass Valve and for the Oil Cooler Bypass Valve is Now in Production {1306, 1314, 1318, 1378}
G3500 Engines Diagnostic Reset Switch
C18 Marine Auxiliary Engines Engine Pressure Sensor Open or Short Circuit - Test
2004/05/03 New Hydraulic Hose Assembly Machine Integrates Crimputer II with Radial Crimping Technology {0738}
2006/06/26 Some Pistons and Cylinder Packs are Cancelled and Replaced {1214}
2004/01/01 A Special Instruction, REHS2060 , "Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump" is Available {1307, 1714}
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Intermittent Engine Shutdown
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C9 Marine Auxiliary and Marine Generator Set Engines Low Power/Poor or No Response to Throttle
Install the Correct Piston Cooling Jet and the Correct Retainer for the One-Piece Piston{1214, 1331} Install the Correct Piston Cooling Jet and the Correct Retainer for the One-Piece Piston{1214, 1331}
C27 and C32 Generator Set Engines CID 0091 FMI 08 Throttle Position signal abnormal