Gear Group (Front) - Remove
拆卸步骤
开始:
- 拆下前壳体。 请参阅拆解和组装, "壳体(前) - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
- 拆下螺栓 (4) 和可调式惰轮 (3) 。
Show/hide table
图 1 | g01037502 |
- 拆下螺栓 (6) 和惰轮 (5) 。
- 拆下螺栓 (2) 和齿轮组组件 (1) 。
- 拆下螺母、螺栓 (9) 和枢轴 (10) 。
Show/hide table
图 2 | g01037504 |
注: 拆卸盘 (13) 时必须要拆下枢轴 (10) 和 (12) 。
注: 如果枢轴 (10) 的螺母松动,或者拆除或移动了枢轴 (10) ,则组装时需要重新调整凸轮轴齿轮和可调式惰轮的齿隙。 请参阅测试和调整, "齿轮组件(前)-定时"。
- 拆下螺母 (11) 、螺栓和枢轴 (12) 。
- 拆下螺栓 (8) 和枢轴 (7) 。
- 拆下将盘 (13) 固定到缸体的锁紧螺栓 (14) 。 拆下盘 (13) 和整体式密封。
Caterpillar Information System:
C3.3 Industrial Engine Water Pump - Remove
Electronic Modular Control Panel II (EMCP II) General Information
795F and 795F AC XQ Off-Highway Truck Steering System Pressure Sensor (Steering Accumulator)
C9 Engine For Caterpillar Built Machines Fuel Transfer Pump - Install
C9 Engine For Caterpillar Built Machines Fuel Transfer Pump - Remove
C9 Marine Engines and C9 Marine Generator Sets Coolant Level Sensor - Remove and Install
3516B HD Generator Set After Starting Engine
EMCP3 Electronic Control Module (Generator Set)
EMCP3 Setpoint Programming
C9 Marine Engines and C9 Marine Generator Sets Electric Starting Motor - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Cold Weather Starting
C9 Marine Auxiliary and Generator Set Engines Starting the Engine
3456 Generator Sets Generator Lead Connections
584 and 584HD Forwarders Guards - Operator Protection
G3500 Engines Speed Sensor
Welding Repair of Motor Grader Frame {0679, 7051} Welding Repair of Motor Grader Frame {0679, 7051}
G3500 Engines Air Starting Motor - Malfunction
G3500 Engines Coolant Level Sensor - Coolant Level Switch
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector
G3500 Engines Alternator - Malfunction
G3500 Engines Coolant in Engine Oil
G3500 Engines Detonation
G3500 Engines Engine Cranks but Will Not Start
G3500 Engines Engine Has Early Wear