Inlet and Exhaust Valve Guides - Remove and Install
Show/hide table
Alat yang Diperlukan | |||
Alat | Nomor Suku Cadang | Keterangan Suku Cadang | Jml |
A | 1U-9169 | Penggerak Pengarah Katup | 1 |
Dimulai dengan:
- Lepaskan katup masuk dan katup buang. Rujuk ke Pembongkaran dan Perakitan, "Katup Masuk dan Katup Buang - Pelepasan dan Pemasangan".
Show/hide table
PERHATIAN |
---|
Pastikan semua suku cadang bersih dari kontaminan. Kontaminan dapat menyebabkan keausan yang cepat dan mempersingkat umur komponen. |
- Gunakan Peralatan (A) untuk melepaskan pengarah katup dari rakitan cylinder head.
Show/hide table
Ilustrasi 1 | g01015291 |
Show/hide table
Alat yang Diperlukan | |||
Alat | Nomor Suku Cadang | Keterangan Suku Cadang | Jml |
B | 124-9057 | Kerah Pemandu | 1 |
9U-6895 | Penggerak Pengarah Katup | 1 |
Show/hide table
PERHATIAN |
---|
Pastikan semua suku cadang bersih dari kontaminan. Kontaminan dapat menyebabkan keausan yang cepat dan mempersingkat umur komponen. |
- Gunakan Peralatan (B) untuk memasang pengarah katup (1). Pasang pengarah katup hingga Panjang (X) berada di atas
20.0 ± 0.5 mm (0.79 ± 0.02 inch) rakitan cylinder head.
Show/hide table
Ilustrasi 2 | g02676390 |
Diakhiri dengan:
- Pasang katup masuk dan katup buang. Rujuk ke Pembongkaran dan Perakitan, "Katup Masuk dan Katup Buang - Pelepasan dan Pemasangan".
Caterpillar Information System:
G3406 Engines Engine Oil Pan
Cat® Digital Voltage Regulator Wiring Diagrams
2004/04/01 New Rocker Arm Improves Lubrication {1123}
G3406 Engines Engine Oil Pan
C11 and C13 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Customer Interface for the 3512B Well Fracturing Engine (ADEM II){1408} Customer Interface for the 3512B Well Fracturing Engine (ADEM II){1408}
2003/09/01 Improved Pump Drive Gear for an Auxiliary Sea Water Pump {1242}
C11 and C13 Engines for Caterpillar Built Machines Front Cover - Install
C15 and C18 Engines for Caterpillar Built Machines Injector Solenoid Circuit - Test
2003/08/01 An Improved Stub Shaft is Used for Engines with Dual Vibration Dampers {1237, 5569}
C11 and C13 Engines for Caterpillar Built Machines Front Cover - Remove
G3520C and G3520E Generator Set Engines Component Location
G3406 Engines Engine Oil Pan
2003/08/04 There Is a New Maximum Temperature for 2W-8147 Gear {1204}
2003/10/01 Fuel Transfer System for Power Modules {1256}
2003/09/01 There Is a New Maximum Temperature for 2W-8147 Gear {1204}
G3520C and G3520E Generator Set Engines Air/Fuel Ratio Control
2003/09/01 There Is a New Maximum Temperature for 2W-8147 Gear {1204}
Installation Instructions for the 240-0716 Tube Kit for the High Pressure Oil Line for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307, 1714} Installation Instructions for the 240-0716 Tube Kit for the High Pressure Oil Line for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307, 1714}
G3500 Generator Sets Ignition System Timing - Check/Adjust
3456 Generator Sets Insulation - Test
C11 and C13 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
3456 Generator Sets Bearing Temperature - Measure/Record
3408C and 3412C Marine Engines Engine Design