Cylinder Head - Remove
Removal Procedure
Start By:
- Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
- Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft And Pushrod - Remove".
- Remove the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive Mounting Group - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Disconnect harness assembly (1), harness assembly (2), and harness assembly (3) .
Show/hide table
Illustration 1 | g01030042 |
- Remove tube assembly (4) .
- Remove tube assembly (5) and tube assembly (6) .
Show/hide table
Illustration 2 | g01030044 |
- Disconnect tube assembly (7) and tube assembly (9) from turbocharger (8) .
Show/hide table
Illustration 3 | g01031525 |
- Attach a suitable lifting device to cylinder head (10) .
Show/hide table
Illustration 4 | g01030056 |
- Remove bolts (11), bolts (12), and washers that hold the cylinder head to the cylinder block. Carefully remove the cylinder head from the cylinder block. The cylinder head weighs approximately 130 kg (287 lb).
Show/hide table
Illustration 5 | g01030059 |
- Remove cylinder head gasket (13) .
Show/hide table
Illustration 6 | g01030060 |
Caterpillar Information System:
C7 On-highway Engine Turbocharger - Install
C7 Engines for Combat and Tactical Vehicles Engine Oil Level Gauge - Calibrate
C7 On-highway Engine Turbocharger - Remove
C15 and C18 Petroleum Generator Sets Parallel Operation
3512C HD SR500 Generator Sets Single Unit Operation
120H and 135H Motor Graders Machine Systems Metering Pump (Steering) - Remove and Install
2003/07/01 Identifying the Prelube Circuit and the Air Start Circuit {1408}
2003/10/01 Policy for Reusing the Turbocharger Turbine Housing {1052, 1065, 7754}
2003/07/01 Replacement of the ECM for Heavy-Duty On-Highway Engines {1901}
3508C, 3512C and 3516C Marine Engines Auxiliary Water Pump - Install
Cat® Digital Voltage Regulator Remote Communication
C11, C13 and C15 On-highway Engines Input Selections
C7 On-highway Engine Cylinder Head - Install
C7 On-highway Engine Electronic Control Module - Remove and Install
2003/07/01 Quality of Remanufactured Camshafts {1210}
C11, C13 and C15 On-highway Engines 0283-07 Intake Valve Actuation Oil Pressure not responding (91)
C11 and C13 Engines Electronic Unit Injector - Remove
C11 and C13 Engines Electronic Unit Injector - Install
C11 and C13 Engines Rocker Shaft and Pushrod - Remove
C11 and C13 Engines Rocker Shaft and Pushrod - Install
C11 and C13 Engines Fuel Filter Base - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C4.4 (Mech) Industrial Engine Electrical System