Engine Oil Pan Plate - Remove and Install
Start By:
- Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
- Remove bolt (3) and the lock. Remove bolts (2) and the locks.
- Remove suction bell and tube (1).
Show/hide table
Illustration 2 g01000908 - Remove bolts (5) and washers that hold engine oil pan plate (4) to the cylinder block. Remove engine oil pan plate (4) and the gasket.
Show/hide table
| |
| Illustration 1 | g01000906 |
- Install a new gasket on engine oil pan plate (4). Use bolts (5) and the washers in order to install engine oil pan plate (4).
Show/hide table
Illustration 5 g01000904 - Place suction bell and tube (1) in position on the engine oil pump.
Show/hide table
Illustration 6 g01000905 - Install bolts (2) and the locks.
- Install bolt (3) and the lock.
Show/hide table
| |
| Illustration 3 | g01000900 |
Show/hide table
| |
| Illustration 4 | g01000901 |
End By:
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Remove
BA-921 Bendix Air Compressor General Troubleshooting Information
G3500B Engines Accumulator - Check
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Assemble
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Disassemble
G3500 Engines MID 014 - CID 0324 - FMI 05 Warning Lamp open/short to ground
G3500 Engines MID 014 - CID 0324 - FMI 03 Warning Lamp short to +batt
G3500 Engines MID 014 - CID 0323 - FMI 05 Shutdown Lamp open/short to ground
G3500 Engines MID 014 - CID 0323 - FMI 03 Shutdown Lamp short to +batt
3044C Industrial Engine and Engines for Caterpillar Built Machines Front Cover - Remove and Install
BA-921 Bendix Air Compressor Discharge Valve Leakage - Test
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
G3500 Engines MID 014 - CID 0325 - FMI 00 Excessive Detonation
C9 Marine Engines Safety Messages
G3500 Engines MID 014 - CID 0326 - FMI 01 Detonation Retarded Timing
G3500 Engines MID 014 - CID 0327 - FMI 02 Number of Detonation Sensors mismatch
2003/06/01 A New Personality Module is Available for G3600 Engines {1902, 7620}
G3500 Engines MID 014 - CID 0328 - FMI 02 Number of Cylinders mismatch
G3500 Engines MID 014 - CID 0329 - FMI 11 Communication Fault with CAT A/F Ratio Control
2003/06/01 Service Literature is Now Available {0375, 7568}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
G3304 and G3306 Engines Valve Guides - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install