Housing (Front) - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean all mating surfaces thoroughly.
- Install a new gasket (3) on the front plate. Be sure that gasket (3) properly fits on the dowel pins.
Note: Do not use sealant on the gasket.
Show/hide table
 | |
| Illustration 1 | g01000873 |
- Apply clean engine oil to the lip of the crankshaft front seal.
Note: If a new crankshaft front seal needs to be installed, refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Position front housing (2) on the front of the cylinder block.
- Install bolts (1) and tighten to a torque of 10 to 13 N·m (7 to 10 lb ft).
End By:
- Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
- Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Remove
BA-921 Bendix Air Compressor General Troubleshooting Information
G3500B Engines Accumulator - Check
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Assemble
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Disassemble
G3500 Engines MID 014 - CID 0324 - FMI 05 Warning Lamp open/short to ground
G3500 Engines MID 014 - CID 0324 - FMI 03 Warning Lamp short to +batt
G3500 Engines MID 014 - CID 0323 - FMI 05 Shutdown Lamp open/short to ground
G3500 Engines MID 014 - CID 0323 - FMI 03 Shutdown Lamp short to +batt
3044C Industrial Engine and Engines for Caterpillar Built Machines Front Cover - Remove and Install
BA-921 Bendix Air Compressor Discharge Valve Leakage - Test
3044C Industrial Engine and Engines for Caterpillar Built Machines Idler Gear - Remove and Install
G3304 and G3306 Engines Engine Oil Pan Plate - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
G3500 Engines MID 014 - CID 0325 - FMI 00 Excessive Detonation
C9 Marine Engines Safety Messages
G3500 Engines MID 014 - CID 0326 - FMI 01 Detonation Retarded Timing
G3500 Engines MID 014 - CID 0327 - FMI 02 Number of Detonation Sensors mismatch
2003/06/01 A New Personality Module is Available for G3600 Engines {1902, 7620}
G3500 Engines MID 014 - CID 0328 - FMI 02 Number of Cylinders mismatch
G3500 Engines MID 014 - CID 0329 - FMI 11 Communication Fault with CAT A/F Ratio Control
2003/06/01 Service Literature is Now Available {0375, 7568}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
G3304 and G3306 Engines Valve Guides - Remove and Install