Electrical System
电气系统是一个负极接地系统。
充电电路在发动机运转过程中工作。 充电电路中的交流发电机产生电气系统使用的直流电。
起动马达
Show/hide table
图 1 | g00894520 |
典型实例 |
起动马达使发动机飞轮转动。 为了维持气缸内的燃油点火操作,转速应足够高。
起动马达有一个电磁阀。 当启动点火开关时,电气系统送来的电压会使电磁阀朝着发动机的飞轮齿圈移动小齿轮。 电磁阀内的电气触点刚好在小齿轮与齿圈啮合前闭合蓄电池和起动马达之间的电路。 这会使起动马达转动。 这种启动形式称为正位移。
当发动机开始运转时,小齿轮驱动装置的超越离合器可以防止电枢损坏。 电枢损坏是因转速过高引起的。 离合器通过切断机械连接来防止损坏。 但在松开点火开关之前,小齿轮仍与齿圈相啮合。 超越离合器中的弹簧可使离合器回到静止位置。
交流发电机
Show/hide table
图 2 | g01278178 |
(1) 皮带轮安装轴 |
交流发电机可以产生下列电气输出:
- 三相电
- 全波电
- 整流电
交流发电机是一个带电刷的机电式部件。 交流发电机经曲轴皮带轮由皮带驱动。 发动机运转过程中交流发电机改变蓄电池的存电量。
交流发电机通过一个安装在皮带轮后面的外部风扇进行冷却。 风扇使空气流入交流发电机前面的孔。 空气通过交流发电机背面的孔流出。
交流发电机将机械能和磁能转化为交流电流和电压。 在三相定子内旋转直流电磁场即可实现这种转化。 电磁场由流过转子的电流产生。 定子产生交流电流和电压。
交流电由三相全波整流器转化为直流电。 直流电流向交流发电机的输出端子。 整流器有三个励磁二极管。 直流电用于充电过程。
固态调节器安装在交流发电机的后端上。 两个电刷将电流导过两个滑环。 电流随后流到转子磁场。 电容器为整流器提供高压保护。
交流发电机经点火开关与蓄电池相连。 因此,交流发电机在开关处于 ON(接通)位置时才发生励磁。
Caterpillar Information System:
C7 and C9 On-Highway Engines Engine Speed/Timing Sensor Circuit - Test
P16, P20, P25, P28, P40 and P60 Pulverizer Reference Material
3056E Industrial Engine Flywheel - Install
3054E Industrial Engine Flywheel - Remove
P16, P20, P25, P28, P40 and P60 Pulverizer Maintenance Interval Schedule
C7 and C9 On-Highway Engines Engine Pressure Sensor Open or Short Circuit - Test
2002/11/01 New Spacer For Marine Oil Pan Gaskets {1302}
3056E Industrial Engine Alternator - Install
3056E Industrial Engine Alternator - Remove
3056E Industrial Engine Electric Starting Motor - Remove and Install
C7 On-highway Engine Piston and Rings
C15 Petroleum Generator Set Engines Electric Starting Motor
C7 and C9 On-Highway Engines Fast Idle Enable Circuit - Test
3500 Spark Ignited Engines Flywheel Housing
C9 Urban Transit Bus Engine Ignition Key Switch Circuit and Battery Supply Circuit - Test
C7 and C9 On-Highway Engines Injection Actuation Pressure Control Valve Circuit - Test
G3406 and G3412 Generator Set Engines Cover Group (Front Housing)
C7 and C9 On-Highway Engines Injector Solenoid Circuit - Test
3500 Spark Ignited Engines Air Control Valve
3054E Industrial Engine Fan - Remove and Install
3054E Industrial Engine V-Belts - Remove and Install
C7 and C9 On-Highway Engines PTO Engine RPM Set Speed (Input A and Input B) Circuit - Test
C11, C13, and C15 On-highway Engines Engine Oil and Filter - Change
C7 and C9 On-Highway Engines Service Brake Pedal Position (Switch 2) Circuit - Test