Correction to Information Regarding the Need for Timing Calibration after Replacing the Engine ECM {1901, 1912, 1912}
- Industrial Engines:
- 3126B (S/N: BEJ1-UP; DCS1-UP)
- C-9 (S/N: CLJ1-UP)
- C-10 (S/N: BCX1-UP)
- C-12 (S/N: BDL1-UP)
- C-15 (S/N: BEM1-UP)
- C-16 (S/N: BFM1-UP)
The above modules contain incorrect information regarding replacement of the Electronic Control Module (ECM). A timing calibration must be performed whenever the engine ECM is replaced. A timing calibration must be performed even if you use the "Copy Configuration - ECM Replacement" feature on the Caterpillar Electronic Technician (Cat ET).
This information can be found in the following topics:
- Troubleshooting, "Replacing the ECM"
- Troubleshooting, "Engine Speed/Timing Sensor Circuit - Test"
- Troubleshooting, "Engine Speed/Timing Sensor - Calibrate"
Please note this correction in the appropriate service manual modules. This information will be corrected in the next revision of the above listed modules.
Caterpillar Information System:
385B and 5090B Excavators Excavator Systems Solenoid Valve (Swing Brake) - Assemble
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Motor
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Motor Control (Travel)
3500 Industrial Engines Woodward UG8 Governor
3126B Engine for Caterpillar Built Machines Air Inlet Heater Circuit - Test
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H and 16H Motor Graders Caterpillar Monitoring System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
2002/03/01 A New Flywheel Housing Gasket Is Now Available For Engines With A PTO {1157, 1165}
CPT372 Truck Mounted Pumper Plate Locations and Film Locations
3512B Marine Auxiliary Engine Thermocouple Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Maintenance Interval Schedule
3408E and 3412E Industrial Engines Low Power/Poor or No Response to Throttle
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Refill Capacities
385B and 5090B Excavators Excavator Systems Solenoid Valve (Swing Brake) - Disassemble
3126B Marine Engines CID 0320 FMI 02 Speed/Timing Sensor Loss of Signal
3126E On-highway Engine Transmission (AT/MT/HT) Relay Circuit - Test
3408E and 3412E Industrial Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
C7 and C9 On-Highway Engines Vehicle Speed and Speedometer Circuit - Test
C7 and C9 On-Highway Engines Wait To Start Lamp Circuit - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Counterbalance Valve
3408E and 3412E Industrial Engines Electrical Power Supply Circuit - Test
C7 and C9 On-Highway Engines Starting Aid Output Circuit - Test
3126E On-highway Engine Warning Lamp Circuit - Test
C7 and C9 On-Highway Engines Vehicle Speed Circuit - Calibrate
3126E On-highway Engine Customer Specified Parameters Worksheet