3126E On-highway Engine Caterpillar

Customer Specified Parameters Worksheet

Usage:

3126E HEP

Show/hide table

Table 1
Selected Engine Rating
Rating Number

Show/hide table

Table 2
ECM Identification Parameters
Vehicle ID

Show/hide table

Table 3
Truck Manufacturer Parameters
Truck Manufacturer
Truck Model Type

Show/hide table

Table 4
Vehicle Speed Parameters
Vehicle Speed Calibration (PPM)
Vehicle Speed CAL (J1939-Trans)
Vehicle Speed CAL (J1939-ABS)
Vehicle Speed Limit (VSL)
VSL Protection (rpm)
Tachometer Calibration (PPR)
Soft Vehicle Speed Limit
Low Speed Range Axle Ratio
High Speed Range Axle Ratio

Show/hide table

Table 5
Cruise Control Parameters
Low Cruise Control Speed Set Limit
High Cruise Control Speed Set Limit
Engine Brake Mode
Cruise/Idle/PTO Switch Configuration
Soft Cruise Control

Show/hide table

Table 6
Idle Parameters
Idle Vehicle Speed Limit
Idle RPM Limit
Idle/PTO RPM Ramp Rate (rpm/sec)
Idle/PTO Bump RPM
Fast Idle RPM (1)
Fast Idle RPM (2)

Show/hide table

Table 7
Dedicated PTO Parameters
PTO Configuration
PTO Top Engine Limit
PTO Engine RPM Set Speed
PTO Engine RPM Set Speed Input A
PTO Engine RPM Set Speed Input B
PTO to Set Speed
PTO Cab Throttle RPM Limit
PTO Vehicle Speed Limit
Torque Limit
PTO Shutdown Time
PTO Activates Cooling Fan
Maximum PTO Enable Speed
Maximum PTO Vehicle Speed
PTO Active Output

Show/hide table

Table 8
Engine/Gear Parameters
Lower Gears Engine RPM Limit
Lower Gears Turn Off Speed
Intermediate Gears Engine RPM Limit
Intermediate Gears Turn Off Speed
Gear Down Protection RPM Limit
Gear Down Protection Turn On Speed
Top Engine Limit (TEL)
Low Idle Engine rpm
Idle Quality Calibration
Transmission Style
AT/MT/HT Part Throttle Shift Speed
Fan Pulley Ratio
Governor Type

Show/hide table

Table 9
Timer Parameters
Idle Shutdown Time (minutes)
Allow Idle Shutdown Override
A/C Switch Fan-On Time
Fan with Engine Brake On
Exhaust Brake Configuration
Warm Up Mode Idle Speed

Show/hide table

Table 10
Engine Monitoring Parameters
Engine Monitoring Mode
Engine Monitoring Lamps (GM only)
Coolant Level Sensor
Oil Pressure Sensor
Oil Level Switch Installation Status GMT-560 Only
Primary Fuel Tank Size GMT-560 Only
Secondary Fuel Tank Size GMT-560 Only

Show/hide table

Table 11
Maintenance Parameters
Maintenance Indicator Mode
PM 1 Interval (Distance/Hrs.)
Engine Oil Capacity (Quarts/Liters)

Show/hide table

Table 12
Trip Parameters
Dash - PM 1 Reset
Dash - Customer Parameters
Theft Deterrent Control System
Theft Deterrent Password
Quick Stop Rate

Show/hide table

Table 13
Input Selections
Transmission Neutral Switch
Exhaust Brake Switch
Torque Limit Switch
Ignore Brake/Clutch Switch
2-Speed Axle Switch
Diagnostic Enable
PTO Engine RPM Set Speed Input B
PTO Engine Shutdown Switch
Cruise Control On/Off Switch
Cruise Control Set/Resume Switch
Cruise Pause Switch
A/C High Pressure Switch
A/C Fan Request Switch
Vehicle Speed Input
Fan Override Switch
Service Brake Pedal Position Switch #1
Clutch Pedal Position Switch

Show/hide table

Table 14
Output Selections
Fast Idle Enable Lamp
Wait To Start Lamp This feature is only available when "Truck Manufacturer" is programmed to "Other".
Change Oil Lamp
Fan Control Type
Engine Running Output
Starting Aid Output

Show/hide table

Table 15
Customer Passwords
Customer Password (1)
Customer Password (2)

Show/hide table

Table 16
Data Link Parameters
Power train Data Link

Current Totals Worksheet

Show/hide table

Table 17
Lifetime Totals
Total Time
Total PTO Time
Total Idle Time
Total Distance
Total Fuel
Total PTO Fuel
Total Idle Fuel

Caterpillar Information System:

C7 and C9 On-Highway Engines Vehicle Speed Circuit - Calibrate

3126E On-highway Engine Warning Lamp Circuit - Test

C7 and C9 On-Highway Engines Starting Aid Output Circuit - Test

3408E and 3412E Industrial Engines Electrical Power Supply Circuit - Test

CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Travel Counterbalance Valve

C7 and C9 On-Highway Engines Wait To Start Lamp Circuit - Test

C7 and C9 On-Highway Engines Vehicle Speed and Speedometer Circuit - Test

3408E and 3412E Industrial Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test

3126E On-highway Engine Transmission (AT/MT/HT) Relay Circuit - Test

3126B Marine Engines CID 0320 FMI 02 Speed/Timing Sensor Loss of Signal

385B and 5090B Excavators Excavator Systems Solenoid Valve (Swing Brake) - Disassemble

2002/03/01 Correction to Information Regarding the Need for Timing Calibration after Replacing the Engine ECM {1901, 1912, 1912}

3126B and 3126E On-highway Engines Engine Speed/Timing Sensor Circuit - Test

CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Oil Makeup (Travel System)

3126E On-highway Engine Injector Solenoid Circuit - Test

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0006 FMI 11 Cylinder #6 Injector fault

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Injection Actuation Pressure Control Valve Circuit - Test

C12 Marine Engine Water Pump - Test

CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive

3500 Generator Set Engines Temperature Switch

3500 Generator Set Engines Temperature Switch

3500 Industrial Engines Temperature Switch

3500 Industrial Engines Temperature Switch

3500 Generator Set Engines Temperature Switch