Fan and Fan Drive - Remove and Install
- Turn the battery disconnect switch to the OFF position.
- Open the hood.
Show/hide table
Illustration 1 g06037372 - Remove fan guard (1).
Show/hide table
Illustration 2 g06037382 - Disconnect harness assembly (2) from the alternator.
Show/hide table
Illustration 3 g06037394 - Remove belt (3). Refer to Operation and Maintenance Manual, Belt - Inspect/Adjust/Replace for the correct procedure.
Show/hide table
Illustration 4 g06037436 - Remove six bolts (5). Remove fan and fan drive (4).
Show/hide table
Illustration 5 g06209939 - Remove bolts (6).
- Remove fan (7) from fan drive (8).
- Install fan and fan drive (4) in the reverse order of removal.
- Tighten bolts (6) to a torque of
23.5 ± 3.5 N·m (208 ± 31 lb in) .
- Tighten bolts (6) to a torque of
Caterpillar Information System:
New Cat Grade Control/Cat Production Measurement Software Is Now Available on Certain 336F XE, 349F XE, 352F XE, 374F and 390F Excavators {7610, 7620} New Cat Grade Control/Cat Production Measurement Software Is Now Available on Certain 336F XE, 349F XE, 352F XE, 374F and 390F Excavators {7610, 7620}
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Swivel Leakage - Test
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Hydraulic Cylinder Leakage - Test
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Speed Control Valve (Hydraulic Cylinder) - Test and Adjust
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Hydraulic Cylinder Cycle Time - Check
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Control Valve Pressure (Hydraulic Rotator) - Test
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Control Manifold - Crossover Relief Valve
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Hydraulic Rotator Cycle Time - Check
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Hydraulic System Air - Purge
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Speed Control Valve
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Gerotor Motor
S2050, S3050, S2070, S3070, S2090 and S3090 Shears Swivel
336 and 336 GC Excavator Capacities (Refill)
A New Turbocharger is Now Used for Certain 390F Hydraulic Excavator Engines {1052, 1053} A New Turbocharger is Now Used for Certain 390F Hydraulic Excavator Engines {1052, 1053}
320D2 FM Forestry Machine Engine Supplement Hood - Remove and Install
Bluetooth Operator ID and Machine Security System (MSS) Normal Operation - Hydraulic Excavators
C9.3B Engines for Caterpillar Built Machines Camshaft Bearings - Remove
Procedure to Replace the Full Open Labyrinth with the Partial Open Labyrinth Motor Housing on the Final Drives for Certain Excavators and Mobile Hydraulic Power Units {4050} Procedure to Replace the Full Open Labyrinth with the Partial Open Labyrinth Motor Housing on the Final Drives for Certain Excavators and Mobile Hydraulic Power Units {4050}
336 and 336 GC Excavator Hydraulic System Oil Filter (Return) - Replace
A New Motor Housing is Now Available for Certain Excavators and Mobile Hydraulic Power Units {4050, 4351} A New Motor Housing is Now Available for Certain Excavators and Mobile Hydraulic Power Units {4050, 4351}
New Water Pump Troubleshooting is Now Used for Certain C15 and C18 Engines {1371, 7569} New Water Pump Troubleshooting is Now Used for Certain C15 and C18 Engines {1371, 7569}
New Water Pump Troubleshooting is Now Used for Certain C15 and C18 Machine Engines {1361, 7569} New Water Pump Troubleshooting is Now Used for Certain C15 and C18 Machine Engines {1361, 7569}
320D2 FM Forestry Machine Engine Supplement Fuel Cooler - Remove and Install
HM208 and HM210 Mulching Heads Drive Hub - Disassemble