Configuration
A configuration is used to enable or set the available features. A configuration should be performed if an Electronic Control Module (ECM) has been replaced or removed.
The Cat® Electronic Technician (Cat ET) service tool is used to access the configuration procedures.
- Connect Cat ET to the machine.
After communication has been established, Cat ET will list the ECMs that are on the machine.
- Choose the menu item "Payload".
- Select the "Service" drop-down menu.
- Select the "Configuration" function.
The list of configurations will appear.
- Select the "Service" drop-down menu.
Show/hide table
Illustration 1 g02158977 Typical example - Select the "Configuration" function.
A list of items will appear.
Show/hide tableIllustration 2 g02159958 Typical Cat ET screen for the "Change Parameter Value" - Select the desired item from the list.
A pop-up that is called "Change Parameter Value" will appear.
- Select "OK".
Ensure that the machine setup has the correct tailgate and liner configuration.
To configure lighting options:
- Connect to Cat ET.
- Select the "Configuration" tool.
- Select "Chassis Configuration" > "Payload Load State Indication Lamp Strategy Configuration" > "Change".
- Ensure that "Value" is set to "TWO LAMPS" configuration. Select "OK".
To configure light overrides:
- Select "ECM" > "Chassis" > "OK".
- Select "Diagnostics" > "Diagnostic Tests".
- Select "Override Parameters".
- Select "Green Payload Lamp" or "Red Payload Lamp" to test that the lamp is functioning.
Toggle function is between "NORMAL", "OFF", or "FLASHING".
Caterpillar Information System:
Rework Procedure for the Control Lever Assembly Is Now Used on Certain 390F Excavators and OEM Excavator Based Specialty Solutions {5070} Rework Procedure for the Control Lever Assembly Is Now Used on Certain 390F Excavators and OEM Excavator Based Specialty Solutions {5070}
Procedure to Install Pin Group for Hydraulic Shear Attachment On Certain Hydraulic Excavators {6344, 6501, 6502} Procedure to Install Pin Group for Hydraulic Shear Attachment On Certain Hydraulic Excavators {6344, 6501, 6502}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Software - Install
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Loaded Machine - Calibrate
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Empty Machine - Calibrate
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Calibration Using Electronic Service Tool
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Connector Contact Description
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application ECM - Replace
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Hydraulic Rotator
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Control Valve (Main)
A New Motor Housing is Now Available on Certain Excavators and Mobile Hydraulic Power Units {4050} A New Motor Housing is Now Available on Certain Excavators and Mobile Hydraulic Power Units {4050}
Procedure to Replace the Full Open Labyrinth with the Partial Open Labyrinth Motor Housing on the Final Drives for Certain Excavators and Mobile Hydraulic Power Units {4050, 4351} Procedure to Replace the Full Open Labyrinth with the Partial Open Labyrinth Motor Housing on the Final Drives for Certain Excavators and Mobile Hydraulic Power Units {4050, 4351}
M314F, M316F, M318F, M320F and M322F Wheeled Excavators Sensor (Data Link Type) - Test
G3516 TA Engine Electronic Service Tools
New Alternator Bracket Assembly is Now Available on Certain 374F and 390F Excavators, Mobile Hydraulic Power Units, and OEM Excavator Based Specialty Solutions {1401, 1402, 1408} New Alternator Bracket Assembly is Now Available on Certain 374F and 390F Excavators, Mobile Hydraulic Power Units, and OEM Excavator Based Specialty Solutions {1401, 1402, 1408}
300.9D and 300.9D VPS Mini Hydraulic Excavator Battery or Battery Cable - Inspect/Replace
Turbocharger Wastegate Actuator Rod on Certain C7.1 Machine Engines {1052} Turbocharger Wastegate Actuator Rod on Certain C7.1 Machine Engines {1052}
Camera View on Display May be Unclear on Certain Cat® Products {7348} Camera View on Display May be Unclear on Certain Cat® Products {7348}
14L Motor Grader Blade Lift Cylinder Socket - Check/Adjust/Replace
C7.1 Engines and Generator Sets CAN Data Link - Test
C7.1 Engines and Generator Sets Coolant Level - Test
C7.1 Engines and Generator Sets Cooling Fan Control - Test - Hydraulic Driven Fan
C7.1 Engines and Generator Sets Cooling Fan Control - Test - Viscous Clutch Fan
C7.1 Engines and Generator Sets Cooling Fan Reversing - Test - Hydraulic Driven Fan