Calibration Using Electronic Service Tool
Calibration With Cat® Electronic Technician (Cat ET)
To perform a calibration with Cat® ET:
- Connect Cat ET.
- Press "Service" on the tool bar.
- Select "Calibrations" in the drop-down menu.
- Select "Payload Calibrations" in the calibration menu.
- Press the Start button at the bottom left of the screen.
- Verify the correct check box is selected.
- Press "Begin".
Before any of the following calibration procedures are carried out, ensure that the:
- Machine is clean.
- Machine is empty.
- Park brake is engaged.
- Ignition switch is ON.
- Machine is parked on level ground with slope no greater than 2%.
Calibrate Inertial Measurement Sensor
- Select "Chassis ECM".
Show/hide table
Illustration 2 g03865812 Select "Service" > "Calibration". - Select "Service" > "Calibrations".
Show/hide table
Illustration 3 g03865816 Select "Inertial Measurement Sensor Calibration" > "Start". - Select "Inertial Measurement Sensor Calibration" > "Start".
Show/hide table
Illustration 4 g03865828 Follow on-screen instructions. Select the "OK" screen. - Follow on-screen instructions. Select the "OK" screen.
Show/hide table
Illustration 5 g06333552 Select "Machine Inertial Measurement Sensor Calibration" > "Begin". - Select "Machine Inertial Measurement Sensor Calibration" > "Begin".
Show/hide table
Illustration 6 g06333594 Follow on-screen instructions. Select "Next". - Follow on-screen instructions. Select "Next".
Show/hide table
Illustration 7 g03865832 "Calibration Successful" message. Select "Finish". - Once calibration has successfully completed, the "Calibration Successful" message will appear. Select "Finish".
Show/hide table
Illustration 8 g03865833 Return to the "ECM Summary" screen. - Return to the "ECM Summary" screen.
Show/hide table
Illustration 1 | g03865807 |
Select "Chassis ECM". |
Caterpillar Information System:
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Connector Contact Description
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application ECM - Replace
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Hydraulic Rotator
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Control Valve (Main)
A New Motor Housing is Now Available on Certain Excavators and Mobile Hydraulic Power Units {4050} A New Motor Housing is Now Available on Certain Excavators and Mobile Hydraulic Power Units {4050}
Procedure to Replace the Full Open Labyrinth with the Partial Open Labyrinth Motor Housing on the Final Drives for Certain Excavators and Mobile Hydraulic Power Units {4050, 4351} Procedure to Replace the Full Open Labyrinth with the Partial Open Labyrinth Motor Housing on the Final Drives for Certain Excavators and Mobile Hydraulic Power Units {4050, 4351}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Wiring Harness (Short Circuit) - Test
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Wiring Harness (Open Circuit) - Test
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Sensor Supply - Test
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Sensor (Data Link Type) - Test
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Electrical Power Supply - Test
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Electrical Connector - Inspect
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Empty Machine - Calibrate
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Loaded Machine - Calibrate
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Software - Install
Procedure to Install Pin Group for Hydraulic Shear Attachment On Certain Hydraulic Excavators {6344, 6501, 6502} Procedure to Install Pin Group for Hydraulic Shear Attachment On Certain Hydraulic Excavators {6344, 6501, 6502}
Rework Procedure for the Control Lever Assembly Is Now Used on Certain 390F Excavators and OEM Excavator Based Specialty Solutions {5070} Rework Procedure for the Control Lever Assembly Is Now Used on Certain 390F Excavators and OEM Excavator Based Specialty Solutions {5070}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Configuration
M314F, M316F, M318F, M320F and M322F Wheeled Excavators Sensor (Data Link Type) - Test
G3516 TA Engine Electronic Service Tools
New Alternator Bracket Assembly is Now Available on Certain 374F and 390F Excavators, Mobile Hydraulic Power Units, and OEM Excavator Based Specialty Solutions {1401, 1402, 1408} New Alternator Bracket Assembly is Now Available on Certain 374F and 390F Excavators, Mobile Hydraulic Power Units, and OEM Excavator Based Specialty Solutions {1401, 1402, 1408}
300.9D and 300.9D VPS Mini Hydraulic Excavator Battery or Battery Cable - Inspect/Replace
Turbocharger Wastegate Actuator Rod on Certain C7.1 Machine Engines {1052} Turbocharger Wastegate Actuator Rod on Certain C7.1 Machine Engines {1052}
Camera View on Display May be Unclear on Certain Cat® Products {7348} Camera View on Display May be Unclear on Certain Cat® Products {7348}