Water Temperature Regulator - Remove and Install - 3054 Engine
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the cooling system. If the engine uses Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses Extended Life Coolant (ELC), refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Remove vent line (1) from the expansion tank.
Show/hide table
 | |
| Illustration 1 | g00851346 |
- Remove vent line (2) .
- Loosen hose clamp (5). Remove hose (6) .
- Remove six bolts (3) that hold the water temperature regulator housing (4) .
- Remove the water temperature regulator. Remove the gasket.
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the gasket surface of the water temperature regulator housing is clean. Ensure that the seat for the water temperature regulator is free of debris.
Show/hide table
| | |
| Illustration 2 | g00851346 |
- Install the water temperature regulator.
- Install a new gasket. Place water temperature regulator housing (4) in position.
- Install six bolts (3). Tighten six bolts (3) .
- Install hose (6) and hose clamp (5). Tighten the hose clamp.
- Install vent line (2) .
- Install vent line (1) onto the expansion tank.
- Fill the cooling system. If the engine uses Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses Extended Life Coolant (ELC), refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Operate the engine. Check for leakage.
Caterpillar Information System:
3176C and 3196 Engines for Caterpillar Built Machines CID 0190 FMI 02 Loss of Engine Speed Signal
3500 Generator Set Engines Piston and Rings
3408E and 3412E Industrial Engines Electrical Ground Stud
3500 Generator Set Engines Fuel Filter Service Indicator
C-10 and C-12 Truck Engines Fuel System - Prime
3046 Engine for Caterpillar Built Machines Turbocharger - Inspect
Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562} Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
3408E and 3412E Industrial Engines Power Take-Off Clutch
CPT372 Truck Mounted Pumper Model View Illustrations
C12 Marine Engine Finding Top Center Position for No. 1 Piston
Power Module Switchgear (Low Voltage and Medium Voltage) Generator Set Control +
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Design
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Cylinder Head
3500 Generator Set Engines Ether Starting Aid
Power Module Switchgear (Low Voltage and Medium Voltage) Battery Charger
3126 Truck Engine (Military) Basic Engine
Engine Oil Cooler Engine Oil Cooler
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Standby Pump Panel General Information
Engine Oil Cooler Component Description
3500B Locomotive Engines Electronic Display Module - Optional
3126 Truck Engine Military Engine Oil Filter Base - Disassemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Design
3126 Truck Engine Military Engine Oil Filter Base - Assemble