Water Temperature Regulator Housing - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to the OEM for the approximate capacity of the cooling system. Refer to the Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change".
Show/hide table
Illustration 1 g01124076 Typical example - Remove the setscrews (4) and the nuts (3).
- Remove the water temperature regulator housing (2) from the cylinder head.
- Remove the gasket (1) from the cylinder head. Discard the gasket.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the mating surfaces of the cylinder head. Clean the mating surfaces of the water temperature regulator housing.
Show/hide table
Illustration 2 g01124076 Typical example - Install a new gasket (1) on the cylinder head.
- Install the water temperature regulator housing (2) to the cylinder head.
- Install the setscrews (4) and the nuts (3) that fasten the water temperature regulator housing to the cylinder head. Tighten the fasteners to a torque of
10 N·m (7.4 lb ft) . - Fill the cooling system with coolant to the correct level. Refer to the Operation and Maintenance Manual, "Refill Capacities" for more information.
Caterpillar Information System:
3408E and 3412E Industrial Engines Power Take-Off Clutch
CPT372 Truck Mounted Pumper Model View Illustrations
C12 Marine Engine Finding Top Center Position for No. 1 Piston
Power Module Switchgear (Low Voltage and Medium Voltage) Generator Set Control +
C12 Marine Engine Electrical System
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Motor - Remove
C15 and C18 Petroleum Generator Sets Radiator Restrictions
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Brake Valve - Install
2002/02/01 New Exhaust Bellows Provide Improved Sealing Of Exhaust Gas {1059}
2002/02/01 A New Gasket Is Used In Turbocharger Groups {1059}
3126 Truck Engine Military Camshaft Bearings - Remove
Electronic Modular Control Panel II (EMCP II) GSC CID 0111 - FMI 03
Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562} Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}
3046 Engine for Caterpillar Built Machines Turbocharger - Inspect
C-10 and C-12 Truck Engines Fuel System - Prime
3500 Generator Set Engines Fuel Filter Service Indicator
3408E and 3412E Industrial Engines Electrical Ground Stud
3500 Generator Set Engines Piston and Rings
3176C and 3196 Engines for Caterpillar Built Machines CID 0190 FMI 02 Loss of Engine Speed Signal
3054 and 3056 Marine Generator Set Engines Water Temperature Regulator - Remove and Install - 3054 Engine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Design
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Cylinder Head
3500 Generator Set Engines Ether Starting Aid
Power Module Switchgear (Low Voltage and Medium Voltage) Battery Charger