Camshaft Bearings - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 8S-2241 | Camshaft Bearing Tool Group | 1 |
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Install Tooling (A). Use Tool (A) to remove the camshaft bearings from the cylinder block.
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly purposes.
Show/hide table
 | |
| Illustration 1 | g00610631 |
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) GSC CID 0111 - FMI 03
Electronic Modular Control Panel II (EMCP II) GSC CID 0110 - FMI 04
3408E and 3412E Industrial Engines Before Starting Engine
Electronic Modular Control Panel II (EMCP II) GSC CID 0110 - FMI 03
3126 Truck Engine Military Camshaft Bearings - Install
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 04
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 03
3054 and 3056 Marine Generator Set Engines Camshaft Bearings - Install
3054 and 3056 Marine Generator Set Engines Camshaft Bearings - Remove
C12 Marine Engines Fuel System - Prime
Electronic Modular Control Panel II (EMCP II) Reading DC Schematics
2002/01/01 Correction to Electronic Troubleshooting, SENR6517, "G3500 Air/Fuel Ratio Control" {1278}
2002/02/01 A New Gasket Is Used In Turbocharger Groups {1059}
2002/02/01 New Exhaust Bellows Provide Improved Sealing Of Exhaust Gas {1059}
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Brake Valve - Install
C15 and C18 Petroleum Generator Sets Radiator Restrictions
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Motor - Remove
C12 Marine Engine Electrical System
Power Module Switchgear (Low Voltage and Medium Voltage) Generator Set Control +
C12 Marine Engine Finding Top Center Position for No. 1 Piston
CPT372 Truck Mounted Pumper Model View Illustrations
3408E and 3412E Industrial Engines Power Take-Off Clutch
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562} Instructions for Installation of Oversize Hydraulic Cylinder Seals {7555, 7562}