E038 Low Engine Coolant Temperature Warning
产生此代码的情况:
电子控制模块(ECM)检测到以下情况:
- 发动机至少运转了两分钟。
- 发动机冷却液温度已升至 75 摄氏度 (167 华氏度)以上
- 发动机冷却液温度降至 70 摄氏度 (158 华氏度)以下的情况达两分钟。
系统响应:
记录此事件。 当温度回升到 75 摄氏度 (167 华氏度)以上时,因冷却液温度低而导致的警告将会关闭。
- 无
- 冷却液温度传感器可能存在问题。
- 水温调节器故障
- 长时间怠速
- 负荷太轻
测试步骤 1. 检查有无当前诊断代码
- 启动卡特彼勒电子技师(ET)。
- 将钥匙开关转到 ON 位置。
- 检查有无当前或记录的诊断代码。
预期结果:
没有任何诊断代码。
结果:
- 与预期结果相符 - 没有任何诊断代码。 继续执行测试步骤 2。
- 与预期结果不相符 - 有诊断代码。
修复: 修正存在的诊断代码。
停止
测试步骤 2. 检查冷却系统
- 检查冷却系统。 测试水温调节器是否正常工作。 调节器卡在开启位置会造成冷却过度。 水温调节器四周有冷却液泄漏也会造成冷却过度。 例如,排放管路泄漏。
注: 有关测试水温调节器的信息,请参考系统操作/测试和调整手册。
预期结果:
水温调节器工作正常。
结果:
- 与预期结果相符 - 水温调节器工作正常。
修复: 环境温度低、负荷轻或发动机转速慢都会造成冷却过度。 此处的冷却过度是由于发动机的热量输入低造成的。
停止
- 与预期结果不相符 - 水温调节器存在问题。
修复: 更换水温调节器。
停止
Caterpillar Information System:
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E040 Low Engine Oil Pressure Shutdown
2001/10/01 New Torque Procedure for the Bushings that Retain the Fuel Injection Pumps (Disassembly and Assembly Manuals) {1251}
2001/10/01 New Torque Procedure for the Bushings that Retain the Fuel Injection Pumps (Testing and Adjusting Manuals) {1251}
3408E and 3412E Industrial Engines Digital Sensor Supply Circuit - Test
2001/09/01 The New Special Instruction, REHS1117-00, "Conversion From 3161 Marine Governor to 723Plus Digital Speed Control With UG Actuator" is Available {1264}
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E279 High Aftercooler Temperature Warning
3524B Engines for Off-Highway Trucks E272 Inlet Air Restriction Warning
2001/10/01 New Torque Procedure for the Bushings that Retain the Fuel Injection Pumps (Specifications Manuals) {1251}
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E173 High Exhaust Temperature Warning
Automatic Transfer Switches CTS, CTSD Series Timers
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E099 Engine Oil Filter Restriction Warning
Electronic Modular Control Panel II (EMCP II) GSC CID 0446 - FMI 12
SCT673 Truck Mounted PumperPOD Model View Illustrations
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E085 Engine Shutdown Overridden
Automatic Transfer Switches CTS, CTSD Series Sensors
3126B and 3126E Truck Engines Electric Starting Motor
2001/09/01 Caterpillar No Longer Recommends The Use Of 195-6071 Spark Plugs Or 195-6353 Spark Plugs On G3300 Engines Or G3400 Engines {1555}
3126 Truck Engine Air Inlet Elbow
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E097 Engine Derate Overridden
Generator Set Start Module (AC Input) Information Plate
2001/09/01 New Main Bearings Provide Improved Bearing Retention in the Cylinder Block {1203}
3054 and 3056 Marine Generator Sets Voltage Connections
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Event Codes
3054 and 3056 Marine Generator Sets Reference Numbers