Maintenance Interval Schedule - 3054B Marine Naturally Aspirated
Note: Before performing any operation or maintenance procedures, ensure that the Safety Information, warnings, and instructions are read and understood.
Battery or Battery Cable - Disconnect
Fuel Control Linkage - Check/Lubricate
Fuel System - Prime
Engine Oil Level - Check
Marine Transmission Oil Level - Check
Walk-Around Inspection
Engine Valve Lash - Inspect/Adjust
Engine Oil and Filter - Change
Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Crankshaft Vibration Damper - Inspect
Engine Air Cleaner Element - Clean/Replace
Engine Crankcase Breather - Clean/Replace
Engine Mounts - Inspect
Engine Oil Sample - Obtain
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Fuel Transfer Pump Strainer - Clean
Heat Exchanger - Inspect
Hoses and Clamps - Inspect/Replace
Marine Transmission Oil Cooler - Clean/Inspect
Cooling System Coolant (DEAC) - Change
Cooling System Water Temperature Regulator - Replace
Fuel Injection Nozzles - Test/Exchange
Starting Motor - Inspect
Water Pump - Inspect
To determine the maintenance intervals, use fuel consumption, service hours, or calendar time, whichever occurs first. Experience has shown that maintenance intervals are most accurately scheduled on the basis of fuel consumption.
Before each consecutive interval is performed, all of the maintenance items from the previous interval must also be performed.
When Required
Battery - ReplaceBattery or Battery Cable - Disconnect
Fuel Control Linkage - Check/Lubricate
Fuel System - Prime
Daily
Cooling System Coolant Level - CheckEngine Oil Level - Check
Marine Transmission Oil Level - Check
Walk-Around Inspection
First 270 L (70 US gal) of Fuel or First 25 to 50 Service Hours
Alternator Belt - Inspect/Adjust/ReplaceEngine Valve Lash - Inspect/Adjust
Every 1875 L (500 US gal) of Fuel or 250 Service Hours or 1 Year
Alternator Belt - Inspect/Adjust/ReplaceEngine Oil and Filter - Change
Every 3750 L (1000 US gal) of Fuel or 500 Service Hours or 1 Year
Auxiliary Water Pump (Rubber Impeller) - InspectBattery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Crankshaft Vibration Damper - Inspect
Engine Air Cleaner Element - Clean/Replace
Engine Crankcase Breather - Clean/Replace
Engine Mounts - Inspect
Engine Oil Sample - Obtain
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Fuel Transfer Pump Strainer - Clean
Heat Exchanger - Inspect
Hoses and Clamps - Inspect/Replace
Every 7500 L (2000 US gal) of Fuel or 1000 Service Hours
Engine Valve Lash - Inspect/AdjustMarine Transmission Oil Cooler - Clean/Inspect
Every 15 000 L (4000 US gal) of Fuel or 2000 Service Hours or 2 Years
Alternator - InspectCooling System Coolant (DEAC) - Change
Cooling System Water Temperature Regulator - Replace
Fuel Injection Nozzles - Test/Exchange
Starting Motor - Inspect
Water Pump - Inspect
Every 22 800 L (6000 US gal) of Fuel or 3000 Service Hours
Cooling System Coolant Extender (ELC) - AddEvery 45 600 L (12 000 US gal) of Fuel or 6000 Service Hours
Cooling System Coolant (ELC) - ChangeEvery 66 400 L (17 500 US gal) of Fuel or 9000 Service Hours
Overhaul ConsiderationsCaterpillar Information System:
Generator Set Start Module System Schematic
3126 Truck Engine Military Cylinder Head - Install
3126 Truck Engine Military Cylinder Head - Remove
3024C Engine for Caterpillar Built Machines Engine Oil Relief Valve
SPS343 Skid Mounted Pumper Junction Box
2001/10/01 Oil Condition Will Affect The Operation of The HEUI Fuel System {1348, 1714}
Automatic Transfer Switches CTS, CTSD Series Functional Test of the Transfer Switch
SPT343 Truck Mounted Pumper Universal Remote Control Console
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pressure Switch
SPS343 Skid Mounted Pumper Reference Material
Automatic Transfer Switches CTG, CTGD Series Transfer Switch - Test
Automatic Transfer Switches CTG, CTGD Series Transfer Mechanism - Lubricate
Automatic Transfer Switches CTS, CTSD Series Engine Control Connections of the Controller
G3408C and G3412C Engines Crankshaft Position for Valve Lash Setting
2001/09/01 Corrections To Operation and Maintenance Manual, SEBU6883-03, "G3408C and G3412C Engines" {7450}
G3408C and G3412C Engines Crankshaft Position for Valve Lash Setting
3126B Industrial Engines System Configuration Parameters
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Shutoff Solenoid
G3408C and G3412C Engines Carburetor - Adjust
3024C Engine for Caterpillar Built Machines Glow Plugs
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Flywheel
2001/09/01 Corrections To Operation and Maintenance Manual, SEBU6682-04, "G3408 and G3412 Engines" {7450}
3024C Engine for Caterpillar Built Machines Flywheel Housing
G3408C and G3412C Engines Gas Pressure