Installation Instruction for 484-7816 Falling Object Guard Kit {7153, 7159} Caterpillar

Excavator

312E to 349E Excavators (Excluding Compact Radius Models)

Introduction

This Special Instruction provides the parts and outlines the installation procedure to install 484-7816 Falling Object Guard Kit on the machines listed above.

Do not perform any of the procedures or order any parts until you have read and understand the instructions contained in this publication.

Safety Section

Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.

A person must be alert to potential hazards. This person must also have the necessary training, skills, and tools to perform these functions properly.

Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance of a potential hazard.

Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Avoid using a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar. If used, ensure the safety of the operating personnel and others.

Ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures.

Operation and maintenance of the machine must not occur unless the instructions and warnings in the machines Operation and Maintenance Manual have been read and are understood.

Show/hide table

Accidental machine starting can cause injury or death to personnel working on the machine. To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps. Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.

Show/hide table

Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.

Show/hide table

Personal injury or death can result from improper lifting or blocking. When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component. Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.

General Information

Graphic Color Description

Color-coding of targeted components, or sections of a part, is used to communicate a required action.

The descriptions below illustrate the different colors and what is represented when used in a graphic.

(Blue) The primary component of focus for a particular step. Target or primary component to be installed or removed. Installation implied unless otherwise noted with a symbol.

(CAT® Yellow) Description of parts.

(Yellow) Components placed aside for access, but not removed. Highlighted areas of adjustment, inspection, or special attention.

(Cyan) Special tools or other equipment required for use in a particular step.

(Light Gray) Components used for reference.

(Magenta) Any fastener, retainer, or electrical connector used to install or remove the primary component.

Graphic Symbol Description

This section includes all the symbol graphics used throughout the Visual Service Procedure (VSP), along with a brief description of what the symbol represents.

Apply Sealant / Glue - To deposit an unbroken line of sealing material having the specified thickness or diameter. To attach with.

Align - Horizontal Center - To arrange or place objects along a line referencing the left to right centers.

Attach - To connect together or to fasten on something.

Clean - To remove foreign or undesired material with a liquid.

Connect - To place in an electrical circuit. To join or fasten together.

Finger Tighten - To apply tension or torque with one's digits unaided by a tool or lever.

Insert - To put in or between.

Level - To position a surface in a horizontal orientation. To position in vertical dimension. To align to assist positioning a surface in a horizontal orientation.

Loosen - To make less tight. To set free. To release.

Lower - To drop to a reduced energy position. To reduce the level of material in a container. To cause to descend.

Open - To unseal or get access to.

Position - To locate to the desired or intended location.

Tighten - To make nearer, to fully stretch, without slack, or to apply tension or torque.

Required Tools

Machine Preparation

Illustration 1	g06160028

Illustration 2	g06155991

Illustration 3	g06156162

Hatch Group

Required Parts

Illustration 4	g06206108

Installation

Illustration 5	g06206189

Illustration 6	g06206195

Illustration 7	g06206200

Illustration 8	g06206210

Overhead Guard Group

Required Parts

Illustration 9	g06154745

Installation

Illustration 10	g06156554

Illustration 11	g06156597

Front Window Guard Group

Required Parts

Illustration 12	g06205931

Installation

Illustration 13	g06206223

Illustration 14	g06206224

Illustration 15	g06206228

Illustration 16	g06206229

Illustration 17	g06206230

Illustration 18	g06206231

Illustration 19	g06206254

Illustration 20	g06206257

Illustration 21	g06206262

Illustration 22	g06206270

Illustration 23	g06206273

Illustration 24	g06206283

Illustration 25	g06206610

Illustration 26	g06206289

Illustration 27	g06206290

Illustration 28	g06206291

Illustration 29	g06206293

Illustration 30	g06206300

Illustration 31	g06206301

Lighting Group

Required Parts

Illustration 32	g06205531

Installation

Illustration 33	g06206303

Illustration 34	g06206304

Mirror Group

Required Parts

Illustration 35	g06205797

Installation

Illustration 36	g06206306

Film Installation

Illustration 37	g06160401

Illustration 38	g06205943