Engine Oil Pump - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a container for storage or disposal.
Show/hide table
Illustration 1 g00762839 - Disconnect oil lines (2) and (3) from pump (1). Plug and cap the oil lines and the pump in order to prevent oil loss and contamination.
Show/hide table
Illustration 2 g00762842 - Remove four bolts (4). Remove pump (1).
Show/hide table
Illustration 3 g00762873 - Remove bolts (5), (6), and (7). Remove the four bolts and bracket (9). Remove adapter (8).
Show/hide table
Illustration 4 g00762890 - Remove four bolts (12). Remove elbow (11) and tube (10).
- Remove the flange and tube (13) from the engine oil cooler bonnet.
Show/hide table
Illustration 5 g00762897 - Install Tool (A) and attach a suitable lifting device to engine oil pump (14).
- Remove bolts (15).
- Remove engine oil pump (14). The weight of the engine oil pump is approximately
39 kg (86 lb) .
Caterpillar Information System:
C-15 and C-16 Industrial Engines Housing (Front)
2000/12/01 A New Coolant Level Sensor is Available {7422}
C-10, C-12, C-15 and C-16 Industrial Engines CAN Data Link Circuit - Test
3500B and 3500B High Displacement Engines for Caterpillar Built Generator Sets Analog Sensor - Calibrate
3516B Power Package Safety Messages
365B, 365B Series II and 365BL Excavators Window Washer Reservoir - Fill
2000/12/01 A New Boost Pressure Sensor is Available {1917}
3054 Engine Alternator - Test
3064 and 3066 Engines for Caterpillar Built Machines Engine Oil Pressure Switch
2001/10/01 A New Configuration of Valve Springs Is Now In Production {1108}
3054 Engine Flywheel - Inspect
3054 Engine Flywheel Housing - Inspect
Marine Monitoring System II General Information
C-15 and C-16 Industrial Engines Air Inlet and Exhaust System
Installation of the 3406B and 3406C Long Block Engines Installation of the 3406B and 3406C Long Block Engines
C-15 and C-16 Industrial Engines Flywheel
2000/12/01 The Oil Seals Have Been Removed From The Exhaust Valves {1100}
325D and 329D Excavators and 325D Material Handler Machine System Specifications Relief Valve (Pilot)
3126 Truck Engine Military Pistons and Connecting Rods - Install
C-15 and C-16 Industrial Engines Fuel System
3126B Engines for Caterpillar Built Machines Cylinder Head - Remove
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Walk-Around Inspection
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Generator Monitoring System Connector Contact Description
2000/12/01 A New Gasket Is Used In An Exhaust Manifold {7555}