Glossary
Show/hide table
Illustration 1 | g02723568 |
Run-time screen icons |
The following icons are depth to grade arrow indicators that indicate direction and relative distance from the target depth:
Show/hide table
Far above grade (Indicated by an Orange arrow pointed down) |
Show/hide table
Near above grade (Indicated by a Green arrow pointed down) |
Show/hide table
On grade (Indicated by two Green arrows pointed towards each other) |
Show/hide table
Near below grade (Indicated by a Green arrow pointed up) |
Show/hide table
Far below grade (Indicated by a Blue arrow pointed up) |
The following icons are system status icons that show status of and type of benchmark that is set:
Show/hide table
No elevation reference |
Show/hide table
Depth from bench |
Show/hide table
Depth from bench - Laser referenced |
Show/hide table
No elevation reference |
Show/hide table
Depth from laser |
The following icons are Linkage Elevation Monitor (LEM) icons that provide the status of the LEM feature:
Show/hide table
Feature not enabled |
Show/hide table
Linkage elevation monitor is enabled, but no limits established. |
Show/hide table
Limits defined for both ceiling and floor. |
Show/hide table
Limits defined for floor only. |
Show/hide table
Limits defined for ceiling only. |
Show/hide table
For the cases when linkage elevation monitor is not available, an exclamation mark is added with the icon to indicate attention required. For example, a sensor is missing where system cannot calculate linkage position. |
Show/hide table
Illustration 2 | g02383197 |
Bucket icon states that show direction of bucket slope and selected bucket focus point |
Show/hide table
Main menu |
Show/hide table
Soft key cycle |
Show/hide table
Heading direction |
Show/hide table
Bench rotation angle (Optional) |
Show/hide table
Benchmark |
Show/hide table
Touchpoint |
Show/hide table
Accept laser |
Show/hide table
Set ceiling |
Show/hide table
Set floor |
The following icons are set depth/slope screen icons:
Show/hide table
Illustration 3 | g02726061 |
Set depth/slope screen |
Show/hide table
Target slope |
Show/hide table
Target slope |
Show/hide table
Target cross slope |
Show/hide table
Target cross slope |
Show/hide table
Main menu |
The main menu icon displays the followingCat Grade Control options menu icons:
Show/hide table
Bucket focus select screen |
Show/hide table
Operating modes screen |
Show/hide table
Tolerance setting screen icon |
Show/hide table
Audible tones configuration screen icon |
Show/hide table
Slope units selection screen icon |
Show/hide table
Linkage elevation monitor settings screen |
Show/hide table
Bucket dimension configuration screen - This icon initiates tilt bucket angle sensor calibration. |
Show/hide table
Work tools select screen - This icon initiates screen to edit dimensions of the selected bucket. |
Caterpillar Information System:
320D and 323D Excavators Lifting Capacities
2011/09/29 An Improved Hose and Clamps are Now Used for the Return Lines Group on the 301.6C and 301.8C Mini Hydraulic Excavators {5057}
2011/09/22 An Improved Hose and Clamps are Now Used for the Return Lines Group on the 302.5C Mini Hydraulic Excavator {5057}
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
320D and 323D Excavators Plate Locations and Film Locations
320D and 323D Excavators Fuel System - Prime
320D and 323D Excavators Circuit Breakers - Reset
204-7392 (Air Motor Driven) Filter Cart {0645, 0680, 0738, 5056, 5068} 204-7392 (Air Motor Driven) Filter Cart {0645, 0680, 0738, 5056, 5068}
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pump - Install
320D and 323D Excavators Fuel System Fourth Filter - Replace - If Equipped
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pump - Remove
312E Excavator Systems Main Hydraulic System
320D and 323D Excavators Radiator Core - Clean
3516C Generator Sets Symbols
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
2011/09/19 Improvements have been Made on the Fan Pulley for Certain 336E Excavators {1384}
Center-Lock Pin Grabber Coupler Work Tool Quick Coupler
374D Excavator Adjustable Gauge Undercarriage Frame
320D and 323D Excavators Monitoring System
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
320D and 323D Excavators Cooling System Coolant Sample (Level 1) - Obtain
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea General Information
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove