Specifications
Engine Specifications
Show/hide table
3618 Engine Specifications     |
|
---|---|
Operating rpm     | 1050     |
Low Idle rpm     | 350     |
Cylinders and Arrangement     | 50 degree vee 18     |
Bore     | 280 mm (11.0 inch)     |
Stroke     | 300 mm (11.8 inch)     |
Displacement     | 18.7 L (1127 cubic inches)     |
Compression Ratio     | 12.5:1     |
Aspiration     | Turbocharged aftercooled     |
Rotation from the flywheel end     | Counterclockwise rotation is standard.     |
Clockwise rotation is optional. | |
Fuel     | See this Operation and Maintenance Manual, "Refill Capacities and Recommendations" (Maintenance Section).     |
Method of Starting     | Air Starting Motors     |
Maximum Allowable Exhaust Back Pressure     | 2.5 kPa (10 inch of H2O)     |
Maximum Allowable Inlet Air Restriction     | 3.7 kPa (15 inches of H2O)     |
Load Profile     | 85% of the operating time at 100% of the rated load 15% of the operating time at less than 50% of the rated load     |
Ambient Conditions (Maximum)     | 45 °C (113 °F) Air 32 °C (90 °F) Sea Water     |
Brake Specific Fuel Consumption     | 205 g/kw h ± 5% tolerance     |
Show/hide table
Illustration 1 | g00744906 |
(A) Exhaust valves (B) Inlet valves (C) Flywheel |
Drives and Gear Trains
Front Drives
Show/hide table
Illustration 2 | g00744903 |
(1) Jacket water pump (2) Aftercooler and oil cooler pump (3) Auxiliary water pump (4) Oil pump (5) Fuel transfer pump |
Show/hide table
Front Drives For 3618 Engines     | |
---|---|
Component     | Speed (1)     |
Jacket Water Pump     | 2653     |
Aftercooler and Oil Cooler Pump     | 2653     |
Auxiliary Water Pump     | 2344     |
Oil Pump     | 1600     |
Fuel Transfer Pump     | 2095     |
Show/hide table
( 1 ) | The speed of the components are listed for an engine that is operating at 1050 rpm. |
Show/hide table
Illustration 3 | g00744904 |
(6) Water outlet (7) Water inlet (8) Auxiliary water outlet (9) Auxiliary water inlet (10) Oil outlet (11) Oil inlet |
Engine Front Gear Train
Show/hide table
Illustration 4 | g00986972 |
(1) Crankshaft (2) Idler (3) Idler (4) Jacket water pump (5) Aftercooler and oil cooler pump (6) Auxiliary water pump (7) Oil pump |
Show/hide table
Front Gear Train For 3618 Engines     | |
---|---|
Gear     | Number Of Teeth     |
(1) Crankshaft     | 96     |
(2) Idler     | 68     |
(3) Idler     | 67     |
(4) Jacket Water Pump     | 38     |
(5) Aftercooler and Oil Cooler Pump     | 38     |
(6) Auxiliary Water Pump     | 43     |
(7) Oil Pump     | 63     |
Engine Rear Gear Train
Show/hide table
Illustration 5 | g00986973 |
(1) Crankshaft (2) Large cluster idler (3) Small cluster idler (4) Camshaft |
Show/hide table
Rear Gear Train For 3618 Engines     | |
---|---|
Gear     | Number Of Teeth     |
(1) Crankshaft     | 83     |
(2) Large Cluster Idler     | 90     |
(3) Small Cluster Idler     | 45     |
(4) Camshaft     | 83     |
Caterpillar Information System:
2000/10/01 New Jake Brake Housing {1119, 1129}
Electronic Modular Control Panel II (EMCP II) Starting Motor Magnetic Switch - Test - PEEC Engines Only
320D and 323D Excavators Machine System Specifications Pilot Valve (One Way)
Electronic Modular Control Panel II (EMCP II) Troubleshooting Dedicated Shutdown Indicators
C9 Engine For Caterpillar Built Machines Turbocharger - Remove
3406E Engine Air Compressor - Remove and Install
3054, 3054B and 3056 Marine Engines Marine Transmission Oil Cooler - Remove and Install - 3056 Engine
3406E Engine Engine Oil Cooler - Install
Electronic Modular Control Panel II (EMCP II) Service Record
Electronic Modular Control Panel II (EMCP II) Block Diagram of Generator Set Control
3126 Truck Engine Military Rocker Shaft - Assemble
2000/10/02 Harness Repair of Alternator R-Terminal Connector {1405, 1408, 7553}
3608 Engine Plate Locations and Film Locations
3054, 3054B and 3056 Marine Engines Water Temperature Regulator Housing - Remove and Install - 3056 Engine
3116 On Highway Engines Pistons and Connecting Rods - Disassemble
3116 On Highway Engines Pistons and Connecting Rods - Remove
3618 Engine Oil Mist Detector - Maintain
2000/11/01 New Turbochargers Are Now Available {1052}
3500B Industrial Engines Electrical Connectors and Functions
3054, 3054B and 3056 Marine Engines Air Cleaner - Remove and Install
2000/10/01 A New Cylinder Liner And A New Combustion Gasket Are Used {1216, 7555}
3618 Engine Metal Particle Detector - Inspect
3406E On-Highway Engine Crankshaft Rear Seal - Install
3406E Engine Engine Control Module - Remove and Install