Flywheel
Show/hide table
Illustration 1 | g00293319 |
Note: Refer to System Operation, Testing and Adjusting for the correct method of inspecting the flywheel.
(1) Bolt
(2) Ring gear
(3) Spring pin
(4) Shoulder
The following instructions should be used during installation of the ring gear:
- Install the flywheel ring gear. Face the "part number" on the ring gear (2) toward the engine block. The flywheel ring gear must be installed against the shoulder (4). The flywheel ring gear can be heated for installation. See table 1. Do not use a torch.
Show/hide table
Table 1 Maximum Temperature     Part Number     Maximum Temperature     6I-2997 Flywheel Ring Gear    
320 °C (608 °F)    1W-1064 Flywheel Ring Gear    
204 °C (400 °F)    
- Press the spring pin (3) into the crankshaft before assembling the flywheel to the crankshaft. Check the distance from the face of the crankshaft to the end of the pin (3) .
Distance ... 11.0 ± 1.0 mm (.43 ± .04 inch)
- Tighten the bolts (1) that hold the flywheel to the crankshaft.
Tighten to the following torque. ... 120 ± 20 N·m (90 ± 15 lb ft)
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Water Pump
Special Instruction For Replacing a 173-7793 Droop Module With a 197-3531 Droop Module{4467} Special Instruction For Replacing a 173-7793 Droop Module With a 197-3531 Droop Module{4467}
G3408C and G3412C Engines Valve Lash and Valve Bridge Adjustment
3126B Industrial Engines Throttle Position Sensor Circuit - Test
CD44B and CD54B Vibratory Asphalt Compactors Engine Compartment - Clean
C-10, C-12, C-15 and C-16 Industrial Engines ECM/Personality Module - Test
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Troubleshooting
Oil Mist Detectors Control Elements and LED Display
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Error Log - Access
C-10, C-12, C-15 and C-16 Industrial Engines Electrical Power Supply Circuit - Test
G3406 Engine Carburetor - Adjust
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Sight Gauge - Clean
2000/10/01 New Combustion Feedback Cable Assembly Helps Prevent Moisture Damage {1563}
3054, 3054B and 3056 Marine Engines Cylinder Head - Remove - 3056 Engine
3054, 3054B and 3056 Marine Engines Water Outlet Manifold - Remove
G3406 Engine Cylinder Liner Projection
3054, 3054B and 3056 Marine Engines Turbocharger - Remove
3054, 3054B and 3056 Marine Engines Cooling System Coolant (DEAC) - Change
3126B and 3126E On-highway Engines Fuel Filter Base - Remove
3126B and 3126E On-highway Engines Fuel Filter Base - Install
3126B and 3126E On-highway Engines Injection Actuation Pressure Control Valve - Remove
3126B and 3126E On-highway Engines Injection Actuation Pressure Control Valve - Disassemble
3126B and 3126E On-highway Engines Injection Actuation Pressure Control Valve - Assemble
3126B and 3126E On-highway Engines Injection Actuation Pressure Control Valve - Install