3126B Industrial Engine Caterpillar


Safety Signs and Labels

Usage:

3126B BEJ
There may be several specific warning signs on an engine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiar with all warning signs.

Ensure that all of the warning signs are legible. Clean the warning signs or replace the warning signs if the words cannot be read or if the pictures are not visible. When the warning signs are cleaned, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the warning signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the warning signs. The warning signs that are loosened could drop off of the engine.

Replace any damaged warning signs or missing warning signs. If a warning sign is attached to a part of the engine that is replaced, install a new warning sign on the replacement part. Any Caterpillar dealer can provide new warning signs.

------ WARNING! ------

Do not operate or work on this engine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.


The warning labels that may be found on the engine are illustrated and described below.

Hydraulic Electronic Unit Injectors



Illustration 1g00737484
Typical Example

The warning label for the hydraulic electronic unit injector is located on the top of the valve cover or on the side of the valve cover.



Illustration 2g00103125

------ WARNING! ------

Electrical shock hazard. The electronic unit injector system uses 90-120 volts.


The Electronic Control Module (ECM) sends a high voltage signal to the injector solenoid. To help prevent personal injury, disconnect the electronic unit injector enable circuit connector. Do not come in contact with the electronic unit injector terminals while the engine is running.

Clutch



Illustration 3g00107406

The warning label for the clutch is located on the clutch housing (if equipped).



Illustration 4g00107407

Rotating gears can cause entanglement of the fingers. Rotating gears can cause entanglement of the hands. Do not service this component without first reading the operator manual.

Engine Lifting



Illustration 5g00367054

The warning label for lifting the engine with a fuel tank is located on the fuel tank (if equipped).



Illustration 6g00100728

------ WARNING! ------

Lift eyes or tank can fail when lifting tank containing fluids resulting in possible personal injury. Drain tank of all fluids before lifting.


Caterpillar Information System:

3126B Industrial Engines Poor Acceleration or Response
C-10, C-12, C-15 and C-16 Industrial Engines Intermittent Engine Shutdown
G3406 Engine Ignition System
C-10 and C-15 Petroleum Engines Low Power/Poor or No Response to Throttle
3508B Industrial Engine with an ADEM 2 Electronic Control Module System Overview
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0175 FMI 04 Engine Oil Temperature short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
C15 and C18 Petrolem Generator Set Engines Service Information Report
SPT343 Truck Mounted Pumper Fan Drive Bearing - Lubricate
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0164 FMI 03 Injector Actuation Pressure voltage high
G3406 Engines Engine Design
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0164 FMI 00 High Injector Actuation Pressure
SPP101 Skid Mounted Pumper Engine Description
Oil Mist Detectors Number 13 LED is Blinking - Troubleshoot
G3406 Engine Lubrication System
Uninterruptible Power Supply (UPS) 250 Commutator Advance Setpoint - Calibrate
Uninterruptible Power Supply (UPS) 250 Vibration Sensors Zeroes - Calibrate
G3406 Engine Cooling System
G3406 Engine Cylinder Block, Liners and Heads
3406E Engine Engine Oil Filter Base - Remove - Engine without BrakeSaver
G3406 Engine Pistons, Rings and Connecting Rods
G3406 Engine Crankshaft
311B, 312B, 315B, 318B, 320B, 322B, 325B, 330B, 345B, 345B Series II, 365B and 385B Excavators Air Conditioning and Heating Blower Motor
G3406 Engine Camshaft
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.