Track Roller - Install
Installation Procedure For The Track Roller On CIPI Undercarriage Arrangements Which Are Based On 325, 325B, and 325C Track Type Excavators
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-7611     | Tube     | 2     |
8S-7615 | Pin     | 2     | |
8S-7640 | Stand     | 2     | |
B     | FT-1310     | Track Roller Lifting Fork     | 1     |
Note: There is a track guide on each side of the machine. The procedure which follows is for the installation of the track roller with the track guide.
- Make sure that the mounting surfaces on the track roller, the track guide, the rock guards (if equipped), and the frame rail are clean and free of dirt and debris prior to installing.
- Use Tooling (B) to put track roller (2) in position on the undercarriage. The weight of the track roller is approximately 45 kg (99 lb).
Note: Make sure that the fill/drain plug in the track roller is facing toward the outside of the undercarriage.
Show/hide table
Illustration 1 | g00489838 |
- Install the four bolts that hold the track roller in position.
- Use Tooling (B) to put track guide (1) in position on the undercarriage. Install the four bolts that secure the guide.
Show/hide table
Illustration 2 | g00489833 |
- Install the rock guards, if equipped.
Show/hide table
Illustration 3 | g00664665 |
(X) Rock guard |
- Prior to lowering the machine to the ground and tightening the track, make sure that all of the track rollers rotate smoothly by manually turning the track rollers.
- Lift the machine off Tooling (A) .
Show/hide table
Illustration 4 | g00489826 |
- Remove Tooling (A) from the machine. Lower the machine to the floor.
- Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track Adjustment - Adjust" for the correct procedure.
Caterpillar Information System:
325, 325B and 325L Excavators Track Roller - Assemble
325, 325B and 325L Excavators Track Roller - Disassemble
325, 325B and 325L Excavators Track Roller - Remove
325, 325B and 325L Excavators Track Carrier Roller - Install
325, 325B and 325L Excavators Track Carrier Roller - Assemble
325, 325B and 325L Excavators Track Carrier Roller - Disassemble
325, 325B and 325L Excavators Track Carrier Roller - Remove
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Install
3500B Engines Auxiliary Water Pump - Assemble - Auxiliary Pump (Type 1)
2000/05/01 Corrections To Disassembly and Assembly Modules, G3600 Engines , "Pistons and Connecting Rods - Install" {1225}
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Remove
325, 325B and 325L Excavators Hydraulic System Pressure - Release
G3406 Engine Overhaul (Major)
325, 325B and 325L Excavators Track - Separate
325, 325B and 325L Excavators Track - Connect
325, 325B and 325L Excavators Front Idler and Recoil Spring - Remove
325, 325B and 325L Excavators Front Idler and Recoil Spring - Install
G3406 Engine Overhaul (Top End)
325, 325B and 325L Excavators Front Idler - Disassemble
325, 325B and 325L Excavators Front Idler - Assemble
325, 325B and 325L Excavators Recoil Spring - Disassemble
3412 Generator Set Engines Fuel Shutoff Solenoid
325, 325B and 325L Excavators Recoil Spring - Assemble
325, 325B and 325L Excavators Track Adjuster - Remove