Pilot Valve (Control Pattern Change) - Disassemble
Disassembly Procedure
Start By:
- Remove the valve. Refer to Disassembly and Assembly, "Pilot Valve (Control Pattern Change) - Remove".
- Remove bolts (1) and cover (2) .
Show/hide table
 | |
| Illustration 1 | g01150001 |
- Remove O-ring seal (3), pins (4), and ball (5) .
Show/hide table
 | |
| Illustration 2 | g01149993 |
- Remove bolts (6) and cover (7) .
Show/hide table
 | |
| Illustration 3 | g01149995 |
- Remove bolt (8), cover (7), and cylinder (9) .
Show/hide table
 | |
| Illustration 4 | g01149998 |
- Remove O-ring seal (10) and sleeve (11) from housing (12) .
Show/hide table
 | |
| Illustration 5 | g01149999 |
Caterpillar Information System:
2005/04/04 An Improved Pin Lock Group for Quick Couplers is Now Available {6129, 6700}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Sea Water Module Interface
2005/03/01 The Cylinder Liners Have a New Appearance {1216}
VHS-10, VHS-30, VHS-40, VHS-50, VHS-60 and VHS-70 Demolition and Scrap Shears Cutting Edge
2005/03/14 The Cylinder Liners Have a New Appearance {1216}
C27 and C32 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
325C LCR Excavator Machine Systems Operator Console - Remove and Install
S320B, S325B, S340B, S365B and S385B Demolition and Scrap Shears Plate Locations and Film Locations
C27 and C32 Generator Set Engines Piston Cooling Jets - Remove and Install
345C Excavator Tool Control System System 16 Prime: Solenoid Valve (Proportional Reducing) - Calibrate - Negative Flow Control
345C Excavator Tool Control System System 16 Prime: Relief Valve (Line) - Test and Adjust - Attachment Control Valve
345C Excavator Tool Control System System 16 Prime: Default Value of Work Tool Parameters
2005/03/21 An Improved Auger Shaft is Now Used {4054, 6282, 7000}
325C LCR Excavator Machine Systems Pilot Valve (Control Pattern Change) - Assemble
C7 and C9 Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve Circuit - Test
VHS-10, VHS-30, VHS-40, VHS-50, VHS-60 and VHS-70 Demolition and Scrap Shears Cutting Edge
C7 Engine for AP-1000D, AP-1055D, BG-2455D, and BG-260D Asphalt Pavers Elevated Idle
M325D Material Handler Machine Systems Stick Cylinder - Remove and Install
2005/07/18 New Seals on the Shaft of the Main Pump and the Shaft of the Swing Pump Prevents Leaks {5070}
BH27, BH30 and BH30 W Skid Steer Loader Backhoes Safety Messages
302.5C Mini Hydraulic Excavator Machine System Specifications Main Hydraulic Pump
994F Wheel Loader Hydraulic System Electronic Control Module (ECM) - Replace
S320B, S325B, S340B, S365B and S385B Demolition and Scrap Shears Wear Plates - Inspect/Replace
345C Excavator Tool Control System Relay (Hydraulic Activation)