Relief Valve (Pilot) - Test and Adjust - No Medium Pressure Control Valve
The pilot relief valve limits the maximum pressure of the pilot hydraulic system.
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Part Description     | Qty     |
8T-0855     | Pressure Gauge (0 to 4,000 kPa (0 to 580 psi))     | 1     |
6V-3989     | Fitting (TEST)     | 1     |
6V-4143     | Quick Connect Coupler     | 2     |
6V-3014     | Hose As     | 1     |
Test
- Stop the engine.
Show/hide table
Illustration 1 | g01205736 |
The remote pressure taps are located behind the left access door. (1) Pressure tap (Pilot pressure) |
- Connect a 4000 kPa (580 psi) pressure gauge to pressure tap (1) .
- Start the engine.
- Adjust the engine speed to HIGH IDLE by turning the engine speed dial to position 10.
- Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
- Check the pilot pressure at pressure tap (1). Refer to Testing and Adjusting, "Specifications" in this manual for the correct pilot pressure.
Adjust
- Loosen locknut (3) .
Show/hide table
Illustration 2 | g01254923 |
Pilot Manifold (2) Cap (Pilot relief valve adjustment screw) (3) Locknut (Pilot relief valve) (4) Pilot relief valve |
- Remove cap (2). Turn pilot relief valve adjustment screw in order to change the pilot pressure.
Note: Turn the adjustment screw clockwise in order to increase the pilot pressure. Turn the adjustment screw counterclockwise in order to decrease the pilot pressure.
- Tighten locknut (3) to the specified torque.
Note: The pressure will increase by approximately 250 kPa (36 psi) when adjustment screw (2) is turned by 1 turn.
Note: Always make the final pressure adjustments on the pressure rise.
Caterpillar Information System:
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Pilot) - Test and Adjust - Medium Pressure Control Valve
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Required Tools
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Flow (Medium Pressure Function) - Test and Adjust
M325C Material Handler Machine Systems Cab - Install
345C, 365C and 385C Excavators Air Conditioning and Heating Motor (Foot and Defroster Air Control)
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Medium Pressure Function) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Hydraulic System - Setup - Hammer Valve
345C Excavator Machine System Specifications Pilot Lines
345C Excavator Tool Control System Switch Status - Check
C-10, C-12, C-15 and C-16 Industrial Engines Engine Speed/Timing Sensor - Calibrate
345C Excavator Machine System Specifications Pump Lines (Main)
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Hydraulic System - Setup - Control Valve (Combined Function)
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Signal Limiter) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Relief Valve (Line) - Test and Adjust - Implement
374F Excavator Swing Drive Oil - Change
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Control Valve (Boom Lowering) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Pressure Switch (Overload Warning) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Control Valve (Stick Lowering) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Margin Pressure - Test and Adjust
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Fan Drive Motor
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Main Pump (Destroke Pressure) - Test and Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Pump Control (Throttle Spool Piston) - Adjust
M313C, M315C, M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Hydraulic System Swing Pump Control (Mechanical Zero) - Test and Adjust