Turbocharger - Remove
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove two bolts (1) from each end of oil drain tube (3). Remove oil drain tube (3) .
Show/hide table
 | |
| Illustration 1 | g00671923 |
Typical Example | |
- Remove tube (4) .
- Remove four bolts (2) .
- Loosen clamp (7) and remove hose (8).
Show/hide table
 | |
| Illustration 2 | g00672021 |
- Remove the bolt and washer (5) .
- Remove the tube (6) .
- Remove air inlet tube (12) .
Show/hide table
 | |
| Illustration 3 | g00672054 |
- Remove four nuts (9) .
- Attach a suitable lifting device (11) to the turbocharger (10) and remove turbocharger (10) from the engine. The weight of the turbocharger is approximately 23 kg (51 lb).
Show/hide table
 | |
| Illustration 4 | g00671930 |
Typical Example | |
Caterpillar Information System:
3500B Engines for Caterpillar Built Power Modules Test for the Water Temperature Regulator
2000/02/07 New Oil Filter Base Group {1306}
Electronic Modular Control Panel II+ (EMCP II+) Normal Mode
3608 Engine Fuel System Operation
3408E and 3412E Engines for Caterpillar Built Machines Water Temperature Regulator - Test
3500B Engines Cylinder Head
3608 Engine Sea Water Cooling System Operation
3176C and 3196 Marine Engines Electronic Unit Injector Sleeve - Remove
3176C and 3196 Marine Engines Electronic Unit Injector - Install
723PLUS Digital Speed Control Watch Window PC Interface
723PLUS Digital Speed Control Programmable Parameters
3176C and 3196 Marine Engines Electronic Unit Injector - Remove
2000/01/01 Correction to Specifications Module, SENR5117-03, "3116 Diesel Truck Engine" {1201}
3500 Generator Set Engines Auxiliary Drive Pulley
2000/01/17 Plastic Cards With The Revised Procedure For Tightening Cylinder Head Bolts Will Be Distributed By Mail {1100}
Programming The Electronic Ignition System (EIS) Control Module For The Manifold Air Pressure (MAP) Sensor.{1408, 1901} Programming The Electronic Ignition System (EIS) Control Module For The Manifold Air Pressure (MAP) Sensor.{1408, 1901}
2000/01/01 Plastic Cards With The Revised Procedure For Tightening Cylinder Head Bolts Will Be Distributed By Mail {1100}
2000/01/01 Plastic Cards With The Revised Procedure For Tightening Cylinder Head Bolts Will Be Distributed By Mail {1100}
3176C and 3196 Marine Engines Turbocharger - Install
3176C and 3196 Marine Engines Valve Mechanism Cover - Remove and Install
3176C and 3196 Marine Engines Rocker Shaft and Pushrod - Remove
2000/02/01 Correction To Troubleshooting, SENR5015-00 {1000}
3176C and 3196 Marine Engines Inlet and Exhaust Valve Springs - Remove and Install
3176C and 3196 Marine Engines Inlet and Exhaust Valves - Remove and Install