Fuel Injector - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 8T-3268     | 单体喷油器拆卸螺栓     | 2     |
开始:
- 拆下气门机构总成。 请参阅拆解和组装, "气门机构 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
发动机起动可能会导致伤亡事故。 发动机起动,可能会伤害操作发动机或在发动机附近的人员。 进行保养工作时,要确保发动机不能起动。 当发动机配备自动起动/停止系统时,这十分重要。 对于配备气动系统的发动机,先关闭气动马达的供气阀,然后开始保修工作。 |
- 切断到发动机的燃料供应。
- 将容器置于燃油压力控制阀 (1) 下方并卸下其中一个顶部螺塞,以排空单体喷油器上的燃油缸盖。
Show/hide table
图 1 | g00639535 |
Show/hide table
注意 |
---|
拆卸油管时,确保排放燃油系统,以避免燃油进入气缸或使燃油流过发动机。 |
- 将供油管组件 (3) 从供油歧管处断开。
Show/hide table
图 2 | g01298982 |
- 通过供油管组件 (3) 将压力调节为207 kPa (30 psi)的干净承压空气引入回油管组件 (2) 。 此举目的是将来自缸盖的燃油驱除到回油歧管中。
- 拆下供油管组件 (3) 和回油管组件 (2) 。 塞上或盖住所有开口。
- 卸下螺栓 (5) 和单体喷油器卡箍 (4) 。
Show/hide table
图 3 | g01299010 |
- 在喷油器上安装工具 (A) 。 均匀地拧紧工具 (A) 以便松开孔中的喷油器。
Show/hide table
注意 |
---|
不要使用柱脚杆撬开单体喷油器,因为这样可能会损坏(弯曲)燃油齿条。 从而致使要更换单体喷油器。 |
- 小心从缸盖上拆下喷油器 (6) 。 在喷油器上打上标记,以便识别缸盖。
Show/hide table
图 4 | g00639538 |
- 将塑料塞安装到缸盖的喷油器孔中。
注: 将一个干净的护盖放到缸盖上方,以防止空气中的浮尘或磨损颗粒进入发动机。
Caterpillar Information System:
SR4 and SR4B Generators and Control Panels Electronic Modular Control Panel II+ with Paralleling (EMCP II+P)
3056 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
3126B and 3126E On-highway Engines Accelerator Pedal (Throttle) Position Sensor Circuit - Test
3612 and 3616 Engines Valve Lifter - Assemble
3612 and 3616 Engines Valve Lifter - Disassemble
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
3612 and 3616 Engines Valve Lifter - Install
SR4 and SR4B Generators and Control Panels Before Starting Engine
3612 and 3616 Engines Valve Lifter - Remove
SR500 Generators Tools
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Remove
330B Excavator Machine System Specifications Recoil Spring
3114, 3116, and 3126 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
3612 and 3616 Engines Fuel Injector - Install
Caterpillar Monitoring System for Electronic Modular Control Panel CID 0102 FMI 08 Pressure Sensor (Boost) Abnormal Signal - Test
3003, 3013, 3014 and 3024 Industrial Engines Engaging the Driven Equipment
C-10 and C-12 Truck Engines Water Pump
3612 and 3616 Engines Cylinder Head - Remove
3618 Engine Crankshaft Main Bearings - Remove
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Conservation Practices
3003, 3013, 3014 and 3024 Industrial Engines Coolant Recommendations
3126B Engines for Caterpillar Built Machines Unit Injector - Remove
3524B Engines for Off-Highway Trucks Can Not Reach Top Engine RPM
3126B Marine Engine Unit Injector - Install